Matrix T3X-05 Скачать руководство пользователя страница 5

Страница: 5 / 78

CHaPTer 2: imPorTaNT SafeTy iNSTrUCTioNS

2.1 before GeTTiNG STarTed

This treadmill is intended for commercial use. To ensure your safety and protect the equipment, read all instructions before operating the Matrix

Treadmill.

LOCATION OF THE TREADMILL

Place the treadmill on a level and stable surface away from direct sunlight. The intense UV light can cause discoloration on the plastics. Locate

your treadmill in an area with cool temperatures and low humidity. Please leave a clear zone behind the treadmill that is at least the width of the

treadmill and at least 79” (2000 mm) long. This zone must be clear of any obstruction and provide the user a clear exit path from the machine. For

ease of access, there should be an accessible space on both sides of the treadmill of at least 24” (600 mm) to allow a user access to the treadmill

from either side. Do not place the treadmill in any area that will block any vent or air openings. The treadmill should not be located in a garage,

covered patio, near water or outdoors.

Содержание T3X-05















































































Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды

Matrix T3X-05, Руководство по обслуживанию

Результаты поиска

Содержание T3X-05

Отзывы:

Похожие инструкции для T3X-05

Бренды по названию

Популярные бренды