Matrix MR311 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 24

Matrix MR311 Скачать руководство пользователя страница 5

5

Using your hob

Gas burners:

Gas flow to the burners is controlled by the control knobs (7 - 11 on the diagram above). There are 3 positions shown on the
control panel. Turning the control knob to the positions shown below achieves the following:

Closed (OFF position)

Maximum position: Provides fast boiling function

Minimum position: Provides simmer function

The hob can be set to the desired position by turning the control knob through the adjustment range in an

anti-clockwise direction..

fig. 2

Gas burners:
1. Left Rapid 3.0kW
2. Left Semi-rapid 1.75kW
3. Triple-ring/Wok 3.7kW
4. Right Semi-rapid 1.75kW
5. Right Rapid 3.0kW

Control panel:
6. Timer control
7. Front left rapid burner control
8. Rear left semi-rapid burner control
9. Centre Triple ring/Wok burner control
10. Rear right semi-rapid burner control
11. Front right rapid burner control
12. Oven/Grill control
13. Light control

This appliance is class 2/1

1

4

3

2

5

6

7

8

9

10

11

12

13

200

«
...
3
4
5
6
7
...
»

Содержание MR311

























Отзывы:

Нет отзывов