Matrix MR311 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 24

Matrix MR311 Скачать руководство пользователя страница 16

16

DOUBLE POLE SWITCHED

FUSE SPUR OUTLET

USE A 3 AMP FUSE

Installation section

THIS APPLIANCE MUST BE CONNECTED TO THE MAINS
SUPPLY BY A COMPETENT PERSON, USING FIXED
WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR
OUTLET AND PROTECTED BY A 3A FUSE.

We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will
comply with the I.E.E. and local regulations.

The wires in the mains lead of this appliance are coloured in
accordance with the following code:

Green & Yellow = Earth, Blue + Neutral, Brown = Live.

As the colour of the wires in the mains feed for the appliance
may not correspond with the coloured markings identifying
the terminals connecting to the fuse spur, proceed as follows:

1. The wire which is coloured green and yellow must be

connected to the terminal marked E (Earth) or

coloured Green.

2. The wire which is coloured blue must be connected to the

terminal marked N (Neutral), or coloured Black.

3. The wire which is coloured brown must be connected to

the terminal marked L (Live), or coloured Red.

Note: Use a 3 AMP Fuse

Assembly and electrical connection should be carried out
by specialised personnel. When installing this product we
recommend you seek the help of another individual.

«
...
14
15
16
17
18
...
»

Содержание MR311

























Отзывы:

Нет отзывов