Matrix MR311 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 24

Matrix MR311 Скачать руководство пользователя страница 15

15

Notes:

•

Do not position this appliance adjacent to a refrigeration

unit. The heat generated may cause the refrigeration unit

to fail.

•

This appliance is designed to be installed adjacent to

cabinet units capable of withstanding temperatures of 65°C

or greater above ambient temperature.

Gas connection

This appliance is supplied with ½” BSP tapered male elbow
connection (fig 17)

Anti-tilt bracket/chain

This appliance is supplied fitted with safety chains and wall
mounted brackets to prevent it tilting forwards. These should
be fitted as part of the installation.

You must ensure that the fixings are suitable for the wall type.
Those included may not be suitable in all situations.

Height adjustable feet

The adjustable feet must be fitted to the base of the range
cooker before use.

Rest the rear of the appliance on the packaging exposing the
base to fit the feet.

Fit the four legs by screwing them hand tight into the support
base. To prevent damage, lift the range cooker into position.
Do not push it across the floor unnecessarily.

fig. 17

«
...
13
14
15
16
17
...
»

Содержание MR311

























Отзывы:

Нет отзывов