Matrix 2016 3x console Скачать руководство пользователя страница 60

Страница: 60 / 63

11.1 sofTWARe UPgRADe InsTRUcTIons foR Ucb

cHAPTeR 11: sofTWARe UPgRADe gUIDe

fIgURe D

fIgURe c

fIgURe b

fIgURe A

note: if you install the software while in a self powered mode, keep pedaling while the software is being installed. after the software

has completely loaded, stop pedaling for 30 seconds to allow the machine to completely power down.

1. Create a file on the USB flash drive which will be used. The folders should be MATRIX\FW\UCB (create a folder called MATRIX, then a folder

in MATRIX called FW, then a folder in FW called UCB - Figure A).

2. Copy the software files into the UCB folder on the USB flash drive (the access should read \MATRIX\FW\UCB - Figure B).

3. Insert the USB flash drive into the USB port on the console.

4. When the display is in home screen, press ENTER, 1, 0, 0, 1, ENTER to enter Manager Mode. Press the UP or DOWN LEVEL keys to

choose the "Software" (Figure C) and press ENTER key -> Press the UP or DOWN LEVEL keys to choose the "Update" and

press ENTER key -> Press the UP or DOWN LEVEL keys to choose the "UCB" (Figure D) and press ENTER key -> Press the UP or

DOWN LEVEL keys to choose the correct software (if there are more than one versions on the USB drive). Once the correct software is

found, press ENTER key and the upgrade procedure will start.

5. After the console beeps and comes back home screen, please remove the USB drive and reset machine power. Note: If the console display

shows 04A0, turn off & turn on the machine again, and the display will go back to standard operation.

6. Enter into Manager Mode and make sure the software version and Machine Type is correct.

Содержание 2016 3x console
































































Результаты поиска

Содержание 2016 3x console

Отзывы:

Бренды по названию

Популярные бренды

Matrix 2016 3x console, Руководство по обслуживанию

Результаты поиска

Содержание 2016 3x console

Отзывы:

Бренды по названию

Популярные бренды