Matrix 2016 3x console, Руководство по обслуживанию

Страница: 26 / 63

24
cHAPTeR 8: TRoUblesHooTIng
8.2 eRRoR coDes lIsT
CODE CLASS DESCRIPTION MACHINE SOLUTION
01A1 C
Incline calibration
error
A
a. It occurs when the calibration time is too long or the calibration distance is too
short.
b. Disconnect the incline tube from the frame. Turn on power and run auto calibration.
- If console still shows error, replace incline motor.
- If no error, reattach incline motor, and replace LCB.
01A3 C
Motor is discon-
nected
T
a. Check the connection of the motor cable at the MCB.
b. Using a multimeter, check the 3 points (U/V/W) and see if there’s a resistance
reading (pins 1 & 2 for U & V, pins 2 & 3 for V & W, pins 1 & 3 for U & W).
- If yes, replace MCB.
- If no, replace motor (a short or open circuiting).
01A8 C
Main motor over
current
T
a. Check the condition of the running deck and belt. Replace the belt and flip or
replace the running deck as needed.
b. Replace the MCB.
01AC C
Resistance over
current.
HUR
Check if the resistance is short circuited by measuring resistance through the power
resistor cable (pins 1 & 4).
- If the resistance value is under 10 ohms, replace the power resistor.
- If the resistance value is over 10 ohms, replace the LCB.
Electro magnet
(ECB) over current.
C
a. On standby mode, measure the resistance on ECB1 and ECB2. Please check
the ECB extension cable connection at the LCB (pins 1 & 3 for ECB1, pins 2 & 4 for
ECB2), there should be between 12.8 ~ 14.2 ohms.
- If the ECB resistance is out of the range, replace the ECB.
- If the ECB resistance is within the range, replace the LCB.
b. Check the gap of ECB1 and ECB2. There should be a gap of .5mm between the
ECB and the flywheel.
01AF C
Electro magnet
(ECB) discon-
nected.
HUR
Check if the Electro-magnet is short circuited or open.
- If the resistance data shows a short/open ohm or is outside the range of 12.8
~14.2 ohms, replace the Electro-magnet.
- If the resistance data is in the range between 12.8 ~14.2 ohms, replace the LCB.
Resistance discon-
nect
A
Check if the resistance is short circuited (pins 1 & 4).
- If resistance data is under 10 ohms, please replace power resistor.
- If resistance data is over 10 ohms, please replace LCB.
Electro magnet
(ECB) discon-
nected.
C
a. Check the connection of the ECB extension cable from the LCB to the ECB.
b. Check to see if LED8 and LED10 on the LCB have a brief light for 3 second when
you power on machine.
- If LED8 and LED10 do not have a brief light, replace the LCB.
- If LED8 and LED10 do have a brief light, check the ECB extension cable connec-
tion at the LCB (pins 1 & 3 for ECB1, pins 2 & 4 for ECB2), there should be between
12.8 ~ 14.2 ohms.
- If the ECB resistance is out of the range, replace the ECB.
- If the ECB resistance is within the range, replace the LCB.
01B4 C
Battery connection
reverses protection.
AHUR
a. Check the battery wire connection between the battery and LCB.
b. Check the battery voltage.
- If there is no data on voltage, replace the battery.
- If there is data on voltage, replace the LCB.
014A
(01AE)
B
LCB charge current
is abnormal
AHUR Replace LCB.
0140 B
Incline motor opera-
tion fail
A
Please run Auto Calibration.
- If the error code happens in Auto-calibration, the machine still can work and no
repairs are needed.
- If the error code happens in workout, please replace the incline motor.
0141 B
Motor over tem-
perature
T
a. Check the connection of the motor cable at the MCB.
b. Use a multi-meter to check the motor wire circuit. Set the multi-meter to Ohms and
place both terminals on the blue wires of the motor cable.
- If there is an Ohm reading above 0, replace the motor.
- If the Ohm reading is 0, replace the MCB.
0144 B Motor over current T
a. Check the condition of the running deck and belt. Replace the belt and flip or
replace the running deck as needed.
b. Replace the MCB.
01XX: Motor Errors