20. ERROR MESSAGE AND RECOVERY OPERATION
If the motor intercepts an abnormal operating condition (such as a system error, the corruption of the information contained in memory, ...), the motor refuses to perform the
manoeuvre commanded and signals the anomaly with 1 downward movement and 1 upward movement, repeated 3 times. If the upper limit switch is NOT stored for contact with an
upper stop, to restore the factory conditions is necessary to reset the motor (see section 21). If the upper limit switch has been stored for contact with an upper stop, you can manually
restore the functionality of the motor, without having to reset it. The restore operation is only possible using a memorized transmitter. The operation of self-restore can be performed
even if the motor does not report anomalies, and always under the supervision of a qualified technician. If the motor fails to complete the recovery manoeuvre (that is, independently
reach the upper stop, see procedure below) it is possible that the motor failure is serious. In this case it is necessary a revision of the motor by the manufacturer.
Reporting on error
x3
This procedure can be performed only if the upper limit switch has been programmed for contact with an upper stop.
Otherwise, the motor does not allow you to perform the recovery process. This procedure should be done only under the
supervision of a qualified technician. The technician is responsible to verify that the motor stops in contact with the upper
stop. Otherwise, it is obligatory to repeat the entire procedure.
5 x STOP
PROG
PROG
TO RESTORE THE MOTOR:
move the motor away from the area of the hooks
01. Press STOP 5 times, than press PROG 1 time.
The motor makes 2 alternate movements.
02. Use UP and DOWN to
.
03. Press briefly PROG.
The motor moves upward.
04. Wait the automatic stop when motor reaches the upper stop.
The motor has been successfully restored!!
08
19. AUTOZERO MODE
If the upper limit switch is stored for contact with an upper stop, you can decide whether the motor must
always reach the upper stop (setting 1 "no release"), if the motor must always reach the upper stop and
drop the fabric briefly (setting 2 "with release"), or if the motor must stop a few inches before the upper stop
and only occasionally (every 30 upward manoeuvres ) reach it (setting 3 "release every 30 manoeuvres").
In any case, each time the motor reaches the upper stop, the stroke is recalibrated in order to recover any
shortening / lengthening of the fabric. The factory set this parameter to 1 (autozero "no release").
N° of movements
Setting
1
2
3
No release
With release
Release every 30 manoeuvres
01. Bring the motor at 50cm from the lower position
The motor signals current setting (from 1 to 3 movements).
05.
06. Wait 10 seconds.
The motor signals new setting (from 1 to 3 movements).
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press DOWN 8 times (briefly and quickly).
The motor performs 3 downward movements.
04. Within 15 seconds, press UP 5 times (briefly and quickly).
Press UP, briefly and quickly, the number of times equal to the desired
setting (from 1 to 3)
19.2 USING COMMAND BUTTONS
Wait 10
seconds
12
3
9
6
5 x UP
ON
8 x DOWN
Press UP from 1 to 3
times (see table)
10.1 UTILIZZANDO IL TRASMETTITORE (solo Atom e Leg)
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate position
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 1 time PREV / 1 times NEXT.
«11» appears on display
04. Press STOP. The motor signals the current
value (1 to 3 movements)
05. Press NEXT the number of times equal to
the desired setting (1 to 3)
06. Press STOP. The motor signals the new
value (1 to 3 movements)
01. Bring the motor in an intermediate position
02. Holding down STOP, press PROG for about
1 sec, until LEDs light
03. Press 1 time UP / 1 times DOWN.
04. Press STOP. The motor signals the current
value (1 to 3 movements)
05. Press DOWN the number of times equal to
the desired setting (1 to 3)
06. Press STOP. The motor signals the newt
value (1 to 3 movements)
01. Bring the motor in an intermediate position
02. Press MENU, «Menu rx» appears on
display
03. Press 1 time PREV / 3 times NEXT.
«11» appears on display
04. Press STOP. The motor signals the current
value (1 to 3 movements)
05. Press UP the number of times equal to the
desired setting (1 to 3)
06. Press STOP. The motor signals the new
value (1 to 3 movements)
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 11»
19.1 USING A TRANSMITTER
21. RESET
21.1 USING A TRANSMITTER
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01.
02.
03.
04.
05.
06.
07. Restore the connections (see diagram on section 4).
08. Reinstall the module
If possible, bring the motor to the intermediate position.
Disconnect the power supply.
Connect as on the diagram.
Connect the power supply. Wait 30 seconds, the motor makes a signal: «
».
If you want to delete also the limit switch wait, otherwise go to point 6.
After 15 seconds, the motor makes another signal: «
».
Disconnect the power supply.
(see section 5 or 6).
Radio code deleted
Limit switch deleted
21.2 USING COMMAND BUTTONS
01. Bring the motor in an intermediate position.
02. Press MENU for about 5 sec, until «rS»
appears on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that the
reset was performed (1 moving up / down).
06.
(see section 5 or 6).
Reinstall the motor
01. Bring the motor in an intermediate position.
02. Holding down STOP, press PROG for
about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The LEDs flash, the motor
performs some movement
05. Press together UP and DOWN for about 2
seconds until the motor indicates that the
reset was performed (1 moving up /
down).
06.
(see section 5 or 6).
Reinstall the motor
01. Bring the motor in an intermediate position.
02. Press MENU, «Menu rx» appears on
display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes, the
motor performs some movement
05. Press together PREV and NEXT for about
2 seconds until the motor indicates that
the reset was performed (1 moving up /
down).
06.
(see section 5 or 6).
Reinstall the motor
See the User manual of
the transmitter at
section:
«RECEIVER MENU -
Function 29 -
Receiver reset»
motor
cable
gray
brown
blue
yellow/green
black
WARNING: This procedure restores the factory settings of the device. This procedure must be carried out by qualified technical personnel. Once the "reset" is
performed, the technician must install this device again (following the procedure on section 05 or 06) and verify proper operation.
L
N