05. INSTALLATION USING THE COMMAND BUTTONS
ON
Connect the power
supply
A
Bring the motor in an
intermediate position
B
(1)
C
x3
D
Without hooks
after the 1°
movement press
briefly a button
Manual hooks
after the 2°
movement press
briefly a button
Automatic hooks
after the 3°
movement press
briefly a button
E
The motor moves
downward
F
Are you using an
offset adapter?
Stop manually
Fine adjustment
required?
NO
YES
Wait
10 seconds
G
H
The motor moves
upward
I
Upper end
by obstacle?
SI
NO
Stop manually
Fine adjustment
required?
NO
YES
Wait
10 seconds
12
3
9
6
J
J
The motor makes a
signal
K
Do you need
to memorize a transmitter?
NO
YES
Wait 15
seconds
12
3
9
6
12
3
9
6
Within 15 s press STOP
of the transmitter
The motor
makes 1 brief
upward
movement
The motor
makes 2 brief
downward
movements
(3)
(4)
(5)
Wait automatic stop
NO
YES
(2)
(1) the motor is in "hold to run" mode: the motor moves in a certain direction until you release the button.
(2) the button must be pressed for 3 times briefly, about 1s between each press and the next. If button is pressed a number other than 3, the motor performs an error message.
(3) elapse about 5 seconds between one movement and the next. If no option is selected, the motor makes a short downward movement. In this case, repeat step 05.C.
(4) now the motor moves in 'pulse' mode: to operate the motor press the button for at least 0.5 seconds; to stop the motor press briefly (less than 0.5 seconds) any button.
(5) you can memorize the transmitter even later (see Section 08 «Memorization - deletion of a radio device»).
Make a fine
adjustment
Make a fine
adjustment
Press together
UP and DOWN
Press together
UP and DOWN
Press together
UP and DOWN
Press together
UP and DOWN
03
1°
2°
3°
Press briefly
the button
that MOVES THE MOTOR DOWN
The motor starts to makes short upward
movements
3 TIMES
Wait automatic
stop
(or stop manually
to set the lower
limit switch)
06. INSTALLATION USING A TRANSMITTER
(1) from the moment you press PROG of the transmitters, the via wire buttons are inhibited for the whole installation procedure.
(2) the motor is in "hold to run" mode: the motor moves in a certain direction until you release the button of the transmitter.
(3) the button must be pressed for 3 times briefly, about 1s between each press and the next. If button is pressed a number other than 3, the motor performs an error message.
(4) elapse about 5 seconds between one movement and the next. If no option is selected, the motor makes a short downward movement. In this case, repeat step 06.E.
(5) now the motor moves in 'pulse' mode: to operate the motor press UP or DOWN of the transmitter; to stop the motor press STOP.
ON
Connect the power
supply
A
Within 15s press PROG
of the transmitter
B
C
Motor moves
upward?
Press UP briefly
YES
NO
Press PROG
of the transmitter
Bring the motor in an
intermediate position
D
(1)
(2)
E
(3)
Pres
STOP 3 times
The motor starts to
makes short upward
movements
x3
Make fine
adjustment
Make fine
adjustment
Press PROG
Press PROG
Press PROG
Press PROG
F
Without hooks
after the 1°
movement press
STOP briefly
Manual hooks
after the 2°
movement press
STOP briefly
Automatic hooks
after the 3°
movement press
STOP briefly
(4)
G
The motor moves
downward
(5)
H
Are you using an
offset adapter?
Stop manually
NO
YES
Fine adjustment
required?
NO
YES
Wait 10
seconds
I
12
3
9
6
J
The motor moves
upward
K
Upper end
by obstacle?
YES
NO
Stop manually
Fine adjustment
required?
NO
YES
Wait 10
seconds
12
3
9
6
J
Wait automatic stop
L
The motor makes a
signal
1°
2°
3°
Wait automatic
stop
(or stop manually
to set the lower
limit switch)