05
09. FINE ADJUSTMENT OF UPPER LIMIT SWITCH
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor to the upper limit switch.
02.
(*).
The motor makes 1 downward movement.
03. Using
and
adjust the upper limit switch.
04. Press
. The motor makes 1 down/up movement.
UP
DOWN
PROG
Press in sequence the
buttons
STOP - PROG - UP
09.1 USING A TRANSMITTER
01. Bring the motor to the upper limit switch.
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press
(briefly and quickly).
04. Within 15 seconds, press
(briefly and quickly).
05. Using
and
adjust the upper limit switch.
06. Wait 10 seconds.
The motor makes 1 down/up movement.
UP 8 times
DOWN 2 times
UP
DOWN
The motor makes 3 small downward movements.
The motor makes 1 small upward movements.
09.2 USING THE COMMAND BUTTONS
WARNING:
The modification of the upper limit switch is not possible if the upper limit switch has been learned by contact with an obstacle.
10. FINE ADJUSTMENT OF LOWER LIMIT SWITCH
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor to the lower limit switch.
02.
(*).
The motor makes 1 downward movement.
03. Using
and
adjust the upper limit switch.
04. Press
. The motor makes 1 up/down movement.
UP
DOWN
PROG
Press in sequence the
buttons
STOP - PROG - DOWN
10.1 USING A TRANSMITTER
01. Bring the motor to the lower limit switch.
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15 seconds, press
(briefly and quickly).
04. Within 15 seconds, press
(briefly and quickly).
05. Using
and
adjust the upper limit switch.
06. Wait 10 seconds.
The motor makes 1 up/down movement.
DOWN 8 times
DOWN 2 times
UP
DOWN
The motor makes 3 small downward movements.
The motor makes 1 small upward movements.
10.2 USING THE COMMAND BUTTONS
STOP
PROG DOWN
PROG
11. MODIFY BOTH THE LIMIT SWITCHES
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor in an intermediate position.
02. Disconnect power supply, wait a few seconds; connect power supply.
03.
(*).
The motor makes 1 up/down movement.
04. Follow as described in section 6, point G and subsequent.
Press in sequence the
buttons
STOP - PROG - STOP
STOP
PROG
STOP
WARNING:
This procedure can change the limit also if it is not completed. For this reason, in case of interruption of the procedure is necessary completely repeat the same.
Go to section
6, point G
ON
12. FAVORITE POSITION
12.1 USING A TRANSMITTER
To memorize:
To recall:
01. Bring motor in the favorite position
02. Press together STOP and FOR ME
for 5 seconds.
03. Motor performs a signal.
01. Press FOR ME
ARCO
To memorize:
To recall:
01. Bring motor in the favorite position
02. Press briefly STOP 6 times and then
hold DOWN for 5 seconds.
03. Motor performs a signal.
01. Press STOP 3 times (briefly)
FLUTE, KUADRO, KORT
To memorize:
To recall:
01. Bring motor in the favorite position
02. Press briefly STOP 6 times and then
hold DOWN for 5 seconds.
03. Motor performs a signal.
01. Press FOR ME
VISIO
Consult the manual of your transmitter in
the section about the functions
associated with the buttons.
Other transmitters...
To memorize:
To recall:
01. Bring the motor in the favorite position.
02. Press DOWN 6 times (briefly and quickly).
01. Press DOWN 2 times (briefly and quickly).
12.2 USING THE COMMAND BUTTONS
STOP
PROG
SU
PROG
Wait 10
seconds
12
3
9
6
2 x DOWN
ON
8 x UP
Wait 10
seconds
12
3
9
6
2 x DOWN
ON
8 x DOWN
6 x DOWN
2 x DOWN
TO MEMORIZE
TO RECALL
13. SUN, WIND, RAIN SENSOR
WARNING! DO NOT memorize radio sensors when motor is set on «manual hooks» mode!!
Sensors generate automatic manoeuvres without notice that can be dangerous. The installer must to inform the end-user and possibly integrate the installation with adequate security
systems. In some situations (eg power loss of motor or sensor, motor failure or sensor, radio noise ...) it is possible that the command imparted by the sensor is not detected by the motor.
The sensor must therefore not be understood as a safety device which ensures the integrity of the roller in every condition, but a means to reduce the possibility that the shutter being
damaged by adverse weather conditions.
13.1 COMPATIBLE SENSORS
Use the sensor series BLAST or BLAST BT or SHAKE (wind sensor), VEGA or VEGA BT (sun/wind sensor), THANK YOU (sun sensor), X11C (rain sensor) with the power supply
AT12. When the sensor detects the presence of wind, the "wind alarm" command is sent: the tuned motors move upward and manual controls are disabled until the end of the alarm.
When the sensor detects the presence of the sun, the "presence of sun" command is sent: the tuned motors move downward. When the sensor detects the absence of the sun, the
"absence of sun" command is sent: the tuned motors move upward. When the sensor detects the presence of rain, the "presence of rain" command is sent: the tuned motors move up
or down, depending on the settings of rain sensor. Each device can store up to 4 sensors wind, only one sun sensor. For more information, consult the manual of sensors.
The function is available only if the motor is set in "No Hooks" mode.