background image

happen about 10 minutes, the meter will be turned 
off automatically. To turn it on, pushing the 

FUNC.

 

Button only. 

 

  REPLACING THE BATTERY   

 

                                       

WARNING

 

To  avoid  electrical  shock  or  personal 

injury,  remove  the  test  leads  and  any 

input  signals  before  replacing  the 

battery.  Replace  only  with  same  type 

of battery.

 

 
 
When the electrical tester displays the “

” mark 

or the backlight be not very lit, the battery must be 
replaced  to  maintain  proper  operation.  Use  the 
following procedure to replacing the battery: 

 

1. 

2. 

 

The  Rotary  Switch  is  used  to  select  OFF. 

Disconnect  test  leads  from  any  live  source 

and  remove  the  test  leads  from  the  input 

terminals. 

 18 

 

3. 

 

4. 

 

5. 

Remove  screws  on  the  battery  cover  and 
open the cover.

 

Remove  the  exhausted  battery  and  replace 
with three new 1.5V size AAA batteries. 
Place battery cover and secure by a screw. 

     

                                         

CAUTION 

Using this appliance in an environment 

with  a  strong  radiated  radio-frequency 

electromagnetic  field  (approximately 

3V/m)  may  influence  its  measuring 

accuracy.   

 

 

  ACCESSORIES   

 

   

Operator’s instruction manual 

 

    Set of test leads 

 

    Gift box 

 

    Battery 1.5V

3

  Size AAA   

 

 

 19 

 

Содержание MS2026R












Отзывы: