Massimo MSU 600 Скачать руководство пользователя

Страница: 79 / 103

STORAGE

Long term storage (60 days or more) of your

machine will require some preventive procedures

to guard against deterioration. After thoroughly

cleaning the machine, prepare for storage as

follows:

1.Drain the fuel system.

2.Remove the spark plug, pour about one

tablespoon of SAE 10W30 or 20W40 motor oil in

the spark plug hole and rein-stall the spark plug.

Ground the spark plug wire and turn the engine

over several times to coat the cylinder wall with

oil.

3.Lubricate all control cables.

4.Block up the frame to raise all wheels off the

ground.

5.Tie a plastic bag over the exhaust pipe outlet to

prevent moisture from entering.

6.If storing in a humid or salt-air cover.

atmosphere, coat all exposed metal surfaces with

a light film of oil. Do not apply oil to any

rubber parts or the seat cover.

7.Remove the battery and charge it. Store it in a

dry place and recharge it once a month. Do not

store the battery in an excessively warm or cold

place (less than 0 °C (30 °F) or more than 30 °C

(90 °F)).

Содержание MSU 600








































































































Результаты поиска

Содержание MSU 600

Отзывы:

Похожие инструкции для MSU 600

Бренды по названию

Популярные бренды

Massimo MSU 600, Руководство пользователя

Результаты поиска

Содержание MSU 600

Отзывы:

Похожие инструкции для MSU 600

Бренды по названию

Популярные бренды