background image

INTRODUCTION 

 

Congratulations on your purchase of the Massimo MSU 600 UTV. With the pur-
chase of this vehicle, you can now appreciate the high degree of craftsmanship. 
This manual will provide you with a good basic understanding of the features 
and operation of this vehicle. This manual includes important safety information. 

It provides information about special techniques and skills necessary to ride your 
vehicle. 

It also includes basic maintenance and inspection procedures. If you 

have any questions regarding the operation or maintenance of your vehicle, 
please consult you dealer. 

 

AN IMPORTANT SAFETY MESSAGE: 
 

● 

READ THIS MANUAL FOR THE VEHICLE RIDER CAREFULLY AND COMPLETELY 

BEFORE OPERATING YOUR VEHICLE. MAKE SURE YOU UNDERSTAND ALL 
INSTRUCTIONS. 
● PAY CLOSE ATTENTION TO THE WARNING AND CAUTION LABELS ON THE 
VEHICLE. 
● NEVER OPERATE A VEHICLE WITHOUT PROPER TRAINING OR INSTRUCTION. 
FREE TRAINING IS AVAILABLE TO ANYONE WHO BUYS A NEW VEHICLE. 
● THIS VEHICLE, AND ANY OTHER VEHICLE OVER 90cc, SHOULD NOT BE RIDDEN 
BY ANYONE UNDER 16 YEARS OF AGE.

 

Содержание MSU 600








































































































Отзывы: