Massimo MSU 600 Скачать руководство пользователя | Manualshive

Страница: 13 / 103

background image

6

described in this manual on level ground. Avoid crossing the side of a steep hill if possible.

Always use proper procedures if you stall or roll backwards when climbing a hill. Maintain a

steady speed when climbing a hill. If you stall or roll backwards, follow the special procedure for
braking described in this manual. Dismount on the uphill side or to a side if pointed straight uphill.
Turn the vehicle around and remount, following the procedure described in this manual.

Always check for obstacles before operating in a new area. Never attempt to operate over large

obstacles, such as large rocks or fallen trees. Always follow proper procedures when operating over
obstacles as described in this manual.

Always be careful when skidding or sliding. Learn to safely control skidding or sliding by

practicing at low speed

and on level, smooth terrain. On extremely slippery surfaces, such as ice, go

slowly and be very cautious in order to reduce the chance of skidding or sliding out of control.

Never operate an vehicle in fast flowing water or in water deeper than that recommended in this

manual. Remember that wet brakes may have reduced stopping ability. Test your brakes after leaving
water. If necessary, apply those several times to let friction dry out the linings.

Always be sure there are no obstacles or people behind you when you operate in reverse. When it

is safe to proceed in reverse, go slowly.

Always use the size and type of tires specified in this manual.

Always maintain proper tire pressure as described in this manual.

Never modify a vehicle through improper installation or use of accessories.

Never exceed the stated load capacity for an vehicle. Cargo should be properly distributed and

securely attached. Reduce speed and follow instructions in this manual for carrying cargo or pulling a
trailer. Allow greater distance for braking.

FOR MORE INFORMATION ABOUT VEHICLE SAFETY,

Please contact

with your dealer.

«
...
11
12
13
14
15
...
»

Содержание MSU 600








































































































Отзывы:

Нет отзывов

Похожие инструкции для MSU 600

Бренд: Polaris Страницы: 147

Бренд: Honda Страницы: 83

Бренд: Klarfit Страницы: 44

Бренд: Ultra-tow Страницы: 9

Бренд: PRONAR Страницы: 99

Бренд: BAIC Страницы: 254

Бренд: Mahindra Страницы: 79

CARRYALL 100 CE

Бренд: Club Car Страницы: 68

Бренд: Cushman Страницы: 186

2014 TERRAIN 1000 72V CE

Бренд: Ezgo Страницы: 71

Бренд: SAFARI Страницы: 50

Бренд: Panther Страницы: 10

Бренд: AC Air Technology Страницы: 49

Бренд: Suzuki Страницы: 26

Бренд: TIMBCO Страницы: 36

Бренд: ROPA Страницы: 564

2009 Ranger RZR

Бренд: Polaris Страницы: 146

Бренд: Monster Moto Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды