Massimo MSU 600 Скачать руководство пользователя

Страница: 78 / 103

CLEANING AND STORAGE

CLEANING

Keep cleaning of your machine will not only

enhance its appearance but will improve its

general performance and extend the useful

life of many components.

Before cleaning the machine:

Ⅰ

a.Block off the end of the exhaust pipe

to prevent water entry. A plastic bag and

strong rubber band may be used.

b. Make sure the spark plug and all filler

caps are properly installed.

Ⅱ

If the engine case is excessively greasy,

apply degreaser with a paint brush. Do not

apply degreaser to the wheel axles.

Ⅲ

Rinse the dirt and degreaser off with a

garden hose. Use only enough pressure to

do the job.

Once the majority of the di

Ⅳ

rt has been hosed

off, wash all surfaces with warm water and

mild, detergent-type soap. An old toothbrush

or bottle brush is handy for hard-to-get-at

places.

Rinse the machine off immediately with

Ⅴ

clean water and dry all surfaces with a

chamois, clean towel or soft absorbent cloth.

Clean the seat with a vinyl upholstery

Ⅵ

cleaner to keep the cover pliable and glossy.

Ⅶ

Automotive type wax may be applied to all

painted and chrome plated surfaces. Avoid

combination cleaner-waxes. Many contain

abrasives which may mar the paint or

protective finish. When finished, start the

engine and let it idle for several minutes.

Содержание MSU 600








































































































Результаты поиска

Содержание MSU 600

Отзывы:

Похожие инструкции для MSU 600

Бренды по названию

Популярные бренды

Massimo MSU 600, Руководство пользователя

Результаты поиска

Содержание MSU 600

Отзывы:

Похожие инструкции для MSU 600

Бренды по названию

Популярные бренды