Martin 90523000 Скачать руководство пользователя | Manualshive

Страница: 27 / 41

background image

Controller operation

27

C

ONTROLLER

OPERATION

6

The FiberSource CMY150 may be programmed and operated with any lighting
controller that is compatible with the USITT DMX standard. This section describes
how to operate the fixture with a controller. See the DMX protocol starting on page
36 for specific control values, and “Data link” on page 12 for connection
requirements.

L A M P C O N T R O L

Important

Avoid striking several lamps at once!

The lamp can be turned on and off from the controller using the lamp-on and lamp-
off commands on channel 1. If the DMX Lamp-off personality is off, the lamp-off
command on channel 1 executes only if each of the CMY channels (3, 4, and 5) is
set to a DMX value from 230 to 232.

Strike lamps one at a time at 5 second intervals. Striking many lamps at once may
cause a voltage drop large enough to prevent lamps from striking, damage
electronics, and trip circuit breakers. To have the lamp strike automatically at
power-up, set the Automatic Lamp-on personality to on (see page 15).

Note: After being turned off, the lamp must cool for approximately 8 minutes
before it can be turned back on.

E F F E C T S

The mechanical effects reset to their home positions when the fixture is powered on.
Effects can also be reset from the controller on channel 1. If the DMX Reset
personality is off, the reset command on channel 1 executes only if each of the
CMY channels is set to a DMX value from 230 to 232.

D i m m e r

The mechanical dimmer provides smooth, high resolution, full-range dimming on
channel 2.

«
...
25
26
27
28
29
...
»

Содержание 90523000










































Отзывы:

Нет отзывов

Похожие инструкции для 90523000

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 2

DIR-655 - Xtreme N Gigabit Router Wireless

Бренд: D-Link Страницы: 3

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 24

Бренд: D-Link Страницы: 20

Бренд: D-Link Страницы: 44

Бренд: D-Link Страницы: 52

Бренд: D-Link Страницы: 103

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Javad Страницы: 35

Бренд: IBM Страницы: 63

Бренд: DCE Страницы: 5

BroadLink SP3353

Бренд: MicroNet Страницы: 66

Бренд: Avolites Страницы: 24

Бренд: ZyXEL Communications Страницы: 485

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды