Martin 90523000 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 41

background image

General operation

17

G

ENERAL

OPERATION

4

G E N E R A L G U I D E L I N E S

For optimum lamp life, turn off the lamp whenever illumination is not required for
extended periods of an hour or more. However it is a good idea to keep the fixture
power on so that the fans continually operate, regardless of whether or not the lamp
is lit. This keeps air circulating internally and prevents condensation from building
up inside the fixture.

When the temperature is expected to fall below freezing, leave the fixture powered
on when not in use to keep the electronics warm. The lamp, however, may be
switched off.

Always allow the lamp to warm up fully before turning it off.

Avoid turning on several lamps at once.

T H E L E D S A N D F I X T U R E O P E R A T I N G

S T A T U S

Two LEDs on the rear panel display the fixture status. Normal operation is indicated
by two green LEDs. See Table 4 for other status messages.

The LEDs flash off for a brief instant at regular intervals to prevent false readings
when the light sensor samples the light level.

Dat

a

Power

Senso

r

«
...
15
16
17
18
19
...
»

Содержание 90523000










































Отзывы:

Нет отзывов

Похожие инструкции для 90523000

Verizon DSL-2750B

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: GE Страницы: 4

Бренд: ZETR Страницы: 2

Бренд: CallDirect Страницы: 33

Бренд: dbx Страницы: 2

Бренд: dbx Страницы: 17

Бренд: LAWO Страницы: 154

Бренд: Patton electronics Страницы: 75

RocketLink-G 3088/I

Бренд: Patton electronics Страницы: 61

Бренд: Patton Страницы: 12

Бренд: Patton Страницы: 84

OnSite 3210 Series

Бренд: Patton Страницы: 110

Бренд: Patton electronics Страницы: 2

SMARTNODE 4110 Series

Бренд: Patton electronics Страницы: 78

Бренд: Patton electronics Страницы: 8

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: Falcon Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды