background image

FIGURE 4A

FINGER SHIELD™ INSTALLATION 

(FOR STEEL DOORS)

  

(See Figures 3, 4A, 4B, 4C)

Finger Shields are furnished for all steel doors up to 9’ (2750) high, 
except Vertical Lift and High Lift over 24“ (670).

1.

Remove the shipping tape holding the finger shields on each 
door section.

2.

With both hands, carefully lay each finger shield face down 
and centered in front of the finger shield clips, at the top of 
each door section.

3.

Lift up the top edge of the door section and place one length 
of cardboard shipping angle under the door section face. 

4.

Start at one end of the door section and with both hands begin 
snapping the finger shield under each finger shield clip.

5.

Use a piece of cardboard for protection, lightly tapping each 
finger shield with a hammer to center the finger shield on
each door section. The finger shield must be centered on the
door section before it is placed in the door opening.

NOTE:   If for some reason a finger shield needs to be removed 
from the finger shield clips, this can be done by pushing the finger 
shield back at the same time it is being pulled away from the finger 
shield clip.   Pulling forward on the finger shield will cause it to grip 
solid on the finger shield clip. Pulling too hard may cause damage.

FIGURE 4B

FIGURE 4C

LOCK-ON BOTTOM
ROLLER BRACKET

ROLLER AND ROLLER SHIELD

#1 DOOR
SECTION

CENTER
STILE

END
STILE

SAW HORSES

FINGER SHIELD
(SNAPPED INTO FIRST
FINGER SHIELD CLIP. 
FOR STEE

)

L DOORS

CARDBOARD
SHIPPING ANGLE

FINGER SHIELD CLIPS
(FOR STEEL DOORS)

LIFT HANDLE

#1 DOOR
SECTION

BOTTOM REINFORCING ANGLE
AND BOTTOM WEATHER SEAL

#1 ROLLER BRACKET,
HINGE, ROLLER, AND
ROLLER SHIELD

CARDBOARD
SHIPPING ANGLE

SAW HORSES

LOCK-ON BOTTOM ROLLER BRACKET

#1 DOOR SECTION

FINGER SHIELD
(FOR STEEL DOORS)

CARDBOARD

HAMMER

(CENTER FINGER SHIELD, 

FOR STEEL

)

 DOORS

CARDBOARD
SHIPPING ANGLE

SAW HORSE

LONG

 STEM ROLLER

ER

LONG

 STEM ROLLER 

ER

AND ROLLER SHIELD

NOTE: Some stee

 models do not include long-stem bottom rollers.

l door

LOW PROFILE
HINGE

LIFT CABLE

5

COPYRIGHT © 2004 MARTIN DOOR

FINGER SHIELD
(SNAPPED INTO FIRST
FINGER SHIELD CLIP. 
FOR STEEL 

)

DOORS

FINGER SHIELD CLIPS
(FOR STEEL DOORS)

FINGER SHIELD CLIPS
(FOR STEEL 

)

DOORS

FINGER SHIELD 
CLIPS (FOR 
STEEL

)

 DOORS

ALL HINGES FASTEN 
FACE DOWN ON 
WOOD DOORS

SCREWS REQUIRED TO 
LOCK-ON BOTTOM ROLLER
BRACKETS TO WOOD DOORS

Содержание MARTIN FINGER SHIELD

























Отзывы: