Marquis MQHBZDV3636 страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 67

background image

HB42 - HOW TO INSTALL CLEAN VIEW KIT (CVCK)

CAUTION: When using CVCK DO NOT INSTALL a Louver assembly

.

1.  Install optional fan kit (see Fan Instruction).
2.  Fold two standoffs up into position and mount with supplied screws. (FIG 1)
3.  Hang CVCK on top of fireplace retainer tabs and rotate down into position. (FIG 2)
4.  Using the screws provided, fasten the non-combustible header onto the top of the CVCK assembly.
5.  Using four supplied #6 screws, fasten CVCK kit to the inside frame of unit.
6.  Kit is supplied with 2 valve extension knobs. Align the notches and slide the extensions onto valve knobs.
7.  DO NOT brick or tile beyond the inside area of the CVCK kit to allow for removal of door.

8.

Install optional pull screen system: First slide curtain onto rods and slide round end of rod into side post (REF A). Using 1/2” DT

screws, mount the flattened end of rod to bottom side of rod hanger bracket (REF B). Repeat this step for opposite side

.

NOTE:

ADDITIONAL ACCESS FOR GASLINE INSTALLATION AND FAN ELECTRICAL INSTALLATION! When CVCK is

installed in framing, remove 2 screws from the right and left side of the bottom panel (REF C). Once screws are removed,

bottom panel can be rotated forward for access to gas valve and fan system.

Clearance to Combustibles

Clearance to Combustibles

Back (from Standoffs)

0 inches/0 mm

Side (from standoffs)

0 inches/0 mm

Floor

0 inches/0 mm

Ceiling (from bottom of fireplace)

60 inches/150 cm

Top (from standoffs)

0 inches/0 mm

Top of 90 degree bend in Minimum

Enclosure of 45 to 46 inches

5 inches/128 mm

/ All Vent Systems

Top of 90 degree bend in

Enclosure over 46 inches

2 1/2 inches/64 mm / All Vent Systems

Top of Horizontal Pipe

1 1/2 inches/38 mm / All Vent Systems

Side & Bottom of Horizontal Pipe

1 inch/25.5mm / All Vent Systems

Vertical Vent Pipe

1 inch/25.5mm / Kingsman Vent Systems

Vertical Vent Pipe

1 1/4 inch/32mm / Simpson/AmeriVent/Selkirk

Direct Temp Systems

WARNING:

Failure to position

the parts in accordance with these

diagrams or failure to use only parts

specifically approved with this

appliance may result in property

damage or personal injury.

NOTE:

When using the Clean View

Kit (CVCK) and installing optional

electrical components (i.e. Remote

Controls, variable speed control, and

or fan modules) locate them in the

Clean View access area, unless other

shielding devices like our IPI

Component box is used.

(NOTE -Floor) if installing the

appliance directly on

carpeting or other combustible

materials other than wood

flooring, the appliance shall be

installed on a metal or wood

panel, the full width and depth

of the appliance. Carpet may

extend 1 inch above the floor

of appliance.

For units with CVCK (Clean

View Circulating Kit) see

framing with CVCK to

establish floor heights

17

«
...
15
16
17
18
19
...
»

Содержание MQHBZDV3636




































































Отзывы:

Нет отзывов

Похожие инструкции для MQHBZDV3636

Бренд: Enviro Страницы: 4

La Valle RF-1591LP

Бренд: Jensen Страницы: 51

Бренд: Majestic Страницы: 3

Бренд: RAIS Страницы: 94

Бренд: Qlima Страницы: 48

e-MatriX 800-500 ST LL

Бренд: Faber Страницы: 24

Бренд: Napoleon Страницы: 2

Superior Fireplaces DRT2000 Series

Бренд: IHP Страницы: 76

Бренд: Heat & Glo LifeStyle Страницы: 26

Бренд: Superior Страницы: 18

Бренд: Jensen Страницы: 45

VIVO 90 COMFORT AIR 11 M1

Бренд: MCZ Страницы: 68

Бренд: Nuu Garden Страницы: 11

Бренд: Glow Fire Страницы: 241

Бренд: Mendip Stoves Страницы: 16

Бренд: Desa Страницы: 28

Бренд: Blumfeldt Страницы: 124

Бренд: Uberhaus Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды