Marquis MQHBZDV3636 страница 40 Скачать руководство пользователя | Manualshive

Страница: 40 / 67

background image

MQHB3636/4236/4736 Gas Conversion –Part A

1. Remove ember plates right and left of burner, ember plates are held in place by 2 screws each.

2. Loosen screws from burner retainer tabs and slide burner to the left to remove from orifice.

3. Remove main orifice using a 1/2” wrench and replace with new conversion orifice.

4. Install new pilot orifice and Hi/Lo valve regulator by following instructions supplied with conversion kit (also See Parts B & C).

5. Adjust the primary air setting to the correct setting as specified in the manual or label plate. To adjust air setting, loosen screw on

the side of air mixing tube and rotate to the correct opening using a drill bit or tape measure. Retighten screw.

6. Reinstall ember plates and burner by reversing steps 1 & 2.

Gas Conversion –Part A – MQRB4236

1. Remove four [4] screws holding down the false bottom. Remove the four [4] screws holding down the burner tube assembly.

2. Slide the burner tube towards the left to remove from orifice.

3. Remove main orifice using a 1/2” wrench and replace with new conversion orifice.

4. Install new pilot orifice and Hi/Lo valve regulator by following instructions supplied with conversion kit (also See Parts B & C).

5. Adjust the primary air setting to the correct setting as specified in the manual or label plate. To adjust air setting, loosen screw on

the side of air mixing tube and rotate to the correct opening using a drill bit or tape measure. Retighten screw.

6. Reinstall false bottom and burner by reversing steps 1 & 2. Pilot Shield must be in placed over pilot assembly.

Caution:

The gas supply shall be shut off prior to disconnecting the electrical power, before proceeding with the conversion

.

WARNING: This conversion kit shall be installed by a qualified service agency in accordance with the

manufacturer’s instruction s and all applicable codes and requirements of the authority having jurisdiction. If the
information in these instructions is not followed exactly a fire, explosion or production of carbon monoxide may result
causing property damage, personal injury or loss of life. The qualified service agency is responsible for the proper
installation of this kit. The installation is not proper and complete until the operation of the converted appliance is checked
as specified in the manufacturer’s instructions supplied with kit.

Air Shutter
(Adjustment)

False Bottom

Main Orifice

Pilot Assembly

Pilot Shield

40

«
...
38
39
40
41
42
...
»

Содержание MQHBZDV3636




































































Отзывы:

Нет отзывов

Похожие инструкции для MQHBZDV3636

Бренд: barbas Страницы: 48

Бренд: barbas Страницы: 32

Бренд: barbas Страницы: 32

Бренд: barbas Страницы: 32

Panorama 110-55 PF2

Бренд: barbas Страницы: 100

Бренд: baltur Страницы: 76

Бренд: Napoleon Страницы: 132

Бренд: Majestic Страницы: 8

Бренд: GDC Страницы: 5

Sovereign Series

Бренд: Majestic Страницы: 24

Бренд: ClassicFlame Страницы: 18

Gemini33xxx SERIES

Бренд: Astria Страницы: 82

Davos A High FP-DAV0A-10L

Бренд: Nordpeis Страницы: 60

SV4.5CTS Series

Бренд: Lennox Hearth Products Страницы: 4

Бренд: Napoleon Страницы: 4

Бренд: Harman Страницы: 28

Бренд: Heat-N-Glo Страницы: 37

Бренд: HEINZE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды