34
33
To “clone” (duplicate) ALL of the memory
contents of one RC2000 Mk
w
w
into another
RC2000 Mk
w
w
, please follow these steps:
1.
Place the source RC2000 Mk
w
(the one with all of the
customized commands, names, macros, macro
sequences, and the like) with its infrared transmitter
window
@3
facing the infrared sensor
@4
of another
“fresh” RC2000 Mk
w
(5 cm, or 2 inches apart).
2.
Press the
CLONE
button
e
of the
source RC2000 Mk
w
with a paper
clip tip, and select “CLONE TX” (clone
transmit) mode (see Figure 17).
3.
Press the
CLONE
button
e
of the
learning (receiving) RC2000 Mk
w
with the tip of a paper clip or a
similar object, and select “CLONE
RX” (clone receive mode). Then
press the
PLAY
button
!5
.
4.
Press the source RC2000 Mk
w
’s transport control
PLAY
!5
key to begin the infrared data transmission
sequence. Now the “LEARN” indicator of receiving
RC2000 Mk
w
starts to blink.
During the transmission, the LCD windows of both
RC2000 Mk
w
remote controls will show a bar-type
indicator, moving from left to right during the
transmission process.
After all bars are lit up on both displays, “TX OK”
(transmission OK) will appear in the source RC2000
Mk
w
’s LCD window, and “RX OK” (reception OK) will
appear in the “cloned” RC2000 Mk
w
’s LCD window,
confirming the end of the copying process (see
Figures 19 and 20).
If the audible beep indicator is on, it will sound to let
you know that cloning is complete.
Please be sure that, during the copying process,
neither RC2000 Mk
w
is physically disturbed (ideally,
they should be placed on a table or other surface,
and not hand-held during the copying process). If,
for some reason, the copying process was
interrupted, the “clone” RC2000 Mk
w
’s LCD display
window will indicate “RX NG” (reception no good).
Simply begin the clone process anew by repeating
the above steps.
5.
If the source RC2000 Mk
w
’s memory contents are at
or near full capacity, the copying process will take
about 3 minutes. After completion of the copying
(cloning) process, press the
CLONE
button on both
RC2000 Mk
w
’s with the paper clip tip, and select the
OFF mode.
Then, you’ll have two identically programmed RC2000
Mk
w
remotes, one of which can again be used as your
system’s primary remote control, and you’ll have the
added confidence of knowing that in the event of
inadvertent programming (or memory contents being
cleared somehow), you can simply retrieve the
“backup” RC2000 Mk
w
that you’ve safely tucked
away, and within minutes restore the programming
contents of the original RC2000 Mk
w
with your
customized configuration.
DSS
MD
VCR
DVD
LD
TV
1
2
3
4
RC-5
USE
LEARN
NAME
D1
D2
D3
D4
D5
D6
D7
D8
MACRO
MACRO
RC2000MK
LEARNING
REMOTE
CONTROL
POWER
ON
OFF
ON/OFF
CLONE
MACRO
MODE
SOURCE
1
OSD
GUIDE
MUTE
VOL
CH
AMP
AUX
TAPE
CD
TUNER
2
3
4
5
6
7
8
9
M
0
C
OK
Approx. 5 cm (2 inches)
Transmitting RC2000 Mk
w
w
Receiving RC2000 Mk
w
w
POWER
ON
OFF
ON/OFF
CLONE
MACRO
MODE
SOURCE
Press the CLONE button.
Figure 17
POWER
ON
OFF
ON/OFF
CLONE
MACRO
MODE
SOURCE
Press the CLONE button.
Figure 18
VOL
CH
AMP
AUX
TAPE
CD
TUNER
Press the PLAY button.
LEARNING REMOTE CONTROL
POWER
ON
OFF
ON/OFF
CLONE
MACRO
MODE
SOURCE
Press on both the receiving and transmitting units.
LEARN
Figure 20
Figure 19
