3-16
A6 - GEAR BOX OIL LEVEL
CHECK
MLT 634 Turbo LSU Série F-E3
MLT 634 -120 LSU Série F-E3
MLT 731 Turbo Série F-E3
MLT 735 Turbo LSU Série 6-E3
MLT 735 -120 LSU Série 6-E3
MLT 741 Turbo LSU Série 6-E3
MLT 741 -120 LSU Série 6-E3
MLT 1035 L Turbo LSU Série 6-E3
Park the lift truck on level ground with the boom raised, the I.C. engine cold and stopped.
Carr y out the control within 5 minutes of the I.C. engine being stopped.
- Remove the plastic cap 1 (fig. A6).
- Remove the dipstick 2 (fig. A6).
- Wipe the dipstick and check the correct level between the two MIN and MAX marks.
- If necessar y, add oil (see: 3 - MAINTENANCE: E3 - GEAR BOX OIL).
- Check visually that there is no leakage or seepage of oil in the transmission.
A6 - GEAR BOX OIL LEVEL
CHECK
MLT 634 -120 LSU POWERSHIFT Série F-E3
MLT 735 -120 LSU POWERSHIFT Série 6-E3
MLT 741 -120 LSU POWERSHIFT Série 6-E3
Park the lift truck on level ground with the boom raised, the I.C. engine cold and stopped.
Carr y out the control within 5 minutes of the I.C. engine being stopped.
- Remove the plastic cap 1 (fig. A6).
- Remove the dipstick 2 (fig. A6).
- Wipe the dipstick and check the correct level between the two MIN and MAX. marks.
- If necessar y, add oil (see: 3 - MAINTENANCE: E3 - GEAR BOX OIL).
- Check visually that there is no leakage or seepage of oil in the transmission.
A7 - TYRES PRESSURE AND WHEEL NUTS TORQUE
CHECK
- Check the condition of the tyres, to detect cuts, protuberances, wear, etc.
- Check the torque load of the wheel nuts. Non compliance with this instruction can cause damage and rupture to the wheel bolts
and distor tion to the wheels.
Wheel nuts tightening torque
• Front tyres: 630 N.m ± 15%
• Rear tyres: 630 N.m ± 15%
- Check and adjust the tyre pressures if necessar y (see: 2 - DESCRIPTION: FRONT AND REAR TYRES).
Check that the air hose is correctly connected to the tyre valve before inflating and keep all persons at a distance during inflation. Respect the
recommended tyre pressures given.
NOTE: There is an OPTIONAL wheel toolkit and anti-puncture kit.
A8 - BOOM PADS
CLEAN - GREASE
To be carried out ever y 10 hours during the first 50 hours ser vice, then once at 250
hours.
- Extend the boom completely.
- With a brush, apply a coat of grease (see: 3 - MAINTENANCE: LUBRICANTS AND FUEL) on
the 4 sides of the telescope(s) (fig. A8).
- Telescope the boom several times in order to spread the coat of grease evenly.
- Remove the surplus of grease.
If the lift truck is used in an abrasive environment (dust, sand, coal…) Use lubricating varnish (MANITOU
reference: 483536). In this respect, consult your dealer.
A6
2
1
A6
1
2
A8
Содержание 6-E3 Series
