Mamiya 645DF Скачать руководство пользователя страница 75

Страница: 75 / 149

7.1.15 AEL/AFL button

Swap the operations of the front and rear

AEL

(Auto Exposure Lock) and

AFL

(Auto Focus Lock) buttons. Find out the location of these buttons

on page 17.

7.1.16 Release Button

Set the AE Lock and AF operations when the shutter release button is
half-pressed. Select one of the following options:

: Activate Auto Focus.

AF & AE

: Activate Auto Focus and Auto Exposure Lock.

Only Release

: Disable the half-press functionality.

7.1.17 AEL

Assign the function of the

AEL

button. The AEL button can lock AE (Auto

Exposure) in one of the following ways:

One Shot: Press the

AEL

button once for the next single exposure to

have the locked setting. This locked exposure setting is released after
the shutter is triggered.

Continuous: Press the

AEL

button once and all subsequent captures

are exposed with the locked

AEL

setting until the

AEL

button is pressed

again.

While Pressed: The AE setting is locked while the AEL button is pressed.

Note:

The AEL functionality is not applicable when the camera is used in

Manual (M) mode.

Содержание 645DF






















































































































































Результаты поиска

Содержание 645DF

Отзывы:

Похожие инструкции для 645DF

Бренды по названию

Популярные бренды

Mamiya 645DF, Руководство пользователя

Результаты поиска

Содержание 645DF

Отзывы:

Похожие инструкции для 645DF

Бренды по названию

Популярные бренды