![background image](http://html.mh-extra.com/html/makita/tw161d/tw161d_instruction-manual_1722947006.webp)
6
ENGLISH
Tips for maintaining maximum
battery life
1 .
Charge the battery cartridge before completely dis-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room tempera-
ture at 10 ° C - 40 ° C (50 ° F - 104 ° F). Let a hot
battery cartridge cool down before charging it.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge.
Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
Fig.1:
1.
R ed ind ic ator
2.
Button
3.
Battery cartridge
To remove the battery cartridge, slide it from the tool
w h ile slid ing th e button on th e f ront of th e c artrid ge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen.
I f not,
it may accidentally fall out of the tool, causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly.
If the cartridge does not slide in easily, it is
not being inserted correctly.
Battery protection system
The tool is equipped with a battery protection system.
This system automatically cuts off power to the motor to
extend battery life.
The tool will automatically stop during operation if the
tool and/or battery are placed under one of the following
c ond itions:
Overloaded:
T h e tool is operated in a manner th at c auses it to d raw
an abnormally high current.
I n th is situation, turn th e tool of f and stop th e applic ation
th at c aused th e tool to bec ome ov erload ed . T h en turn
th e tool on to restart.
If the tool does not start, the battery is overheated. In this
situation, let the battery cool before turning the tool on again.
Low battery voltage:
The remaining battery capacity is too low and the tool
will not operate. If you turn the tool on, the motor runs
again but stops soon. I n th is situation, remov e and
recharge the battery.
Indicating the remaining battery capacity
Only for battery cartridges with the indicator
Fig.2:
1.
I nd ic ator lamps
2.
C h ec k button
Press the check button on the battery cartridge to indi
-
cate the remaining battery capacity. The indicator lamps
ligh t up f or a f ew sec ond s.
Indicator lamps
Remaining
capacity
Lighted
Off
75 % to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
NOTE:
D epend ing on th e c ond itions of use and th e
ambient temperature, the indication may differ slightly
from the actual capacity.
Switch action
Fig.3:
1.
S w itc h trigger
CAUTION:
Before installing the battery car-
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the " OFF" position when released.
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. R elease th e sw itc h trigger to stop.
NOTE:
The tool automatically stops if you keep pull
-
ing th e sw itc h trigger f or about 6 minutes.
Lighting up the front lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Fig.4:
1.
L amp
Fig.5:
1.
Button
P ull th e sw itc h trigger to turn on th e lamp. T o turn of f ,
release it. The lamp goes out approximately seconds
af ter releasing th e sw itc h trigger.
Содержание TW161D
