Makita TW161D, Инструкция по эксплуатации

Страница: 4 / 80

4 ENGLISH
ENGLISH (Original instructions)
SPECIFICATIONS
Model: TW161D
F astening c apac ities S tand ard bolt M8 - M1 6
H igh tensile bolt M6 - M1 2
S q uare d riv e 1 2.7 mm
No load speed H ard impac t mod e 0 - 2,4 00 min
-1
S of t impac t mod e 0 - 1 ,300 min
-1
I mpac ts per minute H ard impac t mod e 0 - 3,6 00 min
-1
S of t impac t mod e 0 - 2,000 min
-1
O v erall length 1 5 0 mm
R ated v oltage D .C . 1 0.8 V - 1 2 V max
Net w eigh t 1 .0 - 1 .2 kg
Due to our continuing program of research and development, the specifications herein are subject to change
w ith out notic e.
Specifications may differ from country to country.
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi
-
est c ombination, ac c ord ing to EP T A -P roc ed ure 01 / 201 4 , are sh ow n in th e table.
Applicable battery cartridge and charger
Battery cartridge
BL 1 01 5 / BL 1 01 6 / BL 1 020B / BL 1 021 B / BL 1 04 0B / BL 1 04 1 B
C h arger D C 1 0S A / D C 1 0S B / D C 1 0W C / D C 1 0W D / D C 1 8 R E
Some of the battery cartridges and chargers listed above may not be available depending on your region of
resid enc e.
WARNING:
Only use the battery cartridges and chargers listed above.
Use of any other battery cartridges
and chargers may cause injury and/or fire.
Intended use
T h e tool is intend ed f or f astening bolts and nuts.
Noise
The typical A-weighted noise level determined accord
-
ing to EN6 28 4 1 -2-2:
Sound pressure level (L
pA
) : dB(A)
Sound power level (L
W A
) : dB (A)
Uncertainty (K) : dB(A)
NOTE:
The declared noise emission value(s) has
been measured in ac c ord anc e w ith a stand ard test
method and may be used for comparing one tool with
anoth er.
NOTE:
The declared noise emission value(s)
may also be used in a preliminary assessment of
ex posure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter
-
mined ac c ord ing to EN6 28 4 1 -2-2:
W
ork mod e: impac t tigh tening of f asteners of th e max i-
mum capacity of the tool
Vibration emission (a
h
) : . m/s
2
Uncertainty (K) : . m/s
2
NOTE:
The declared vibration total value(s) has been
measured in ac c ord anc e w ith a stand ard test meth od
and may be used for comparing one tool with another.
NOTE:
The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.