11 ENGLISH
NOTE:
Depending on the conditions of use and the
ambient temperature, the indication may differ slightly
from the actual capacity.
NOTE:
The first (far left) indicator lamp will blink when
the battery protection system works.
Tool / battery protection system
The tool is equipped with a tool/battery protection sys
-
tem. This system automatically cuts off power to the
motor to extend tool and battery life. The tool will auto
-
matically stop during operation if the tool or battery is
placed under one of the following conditions:
Overload protection
When the tool or battery is operated in a manner that
causes it to draw an abnormally high current, the tool
automatically stops without any indication. In this sit
-
uation, turn the tool off and stop the application that
caused the tool to become overloaded. Then turn the
tool on to restart.
Overheat protection
When the tool or battery is overheated, the tool stops
automatically. In this case, let the tool and battery cool
before turning the tool on again.
NOTE:
When the tool is overheated, the bottom lamp
blinks.
Overdischarge protection
When the battery capacity is not enough, the tool stops
automatically. In this case, remove the battery from the
tool and charge the battery.
Protections against other causes
Protection system is also designed for other causes
that could damage the tool and allows the tool to stop
automatically. Take all the following steps to clear the
causes, when the tool has been brought to a temporary
halt or stop in operation.
1.
Turn the tool off, and then turn it on again to restart.
2. Charge the battery(ies) or replace it/them with
recharged battery(ies).
3. Let the tool and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
Switch action
WARNING:
Before installing the battery car-
tridge into the tool, always check to see that the
switch lever actuates properly and returns to the
"OFF" position when released.
To start the tool, press the power switch to light up the
power indicator lamp in green and then squeeze the
switch lever. Release the switch lever to stop. To turn off
the power of the tool, press the power switch to turn off
the indicator lamp. Also, the power of the tool goes out
approximately 5 minutes after releasing the switch lever.
►
Fig.3:
1.
Power switch
2.
Power indicator lamp
3.
Switch lever
Lighting up the bottom lamp
CAUTION:
Do not look in the light or see the
source of light directly.
Switch on the tool by pressing the power switch and
squeeze the switch lever to light up the bottom lamp.
The bottom lamp keeps on lighting while the switch
lever is being squeezed. The bottom lamp goes out
when the power switch is turned off or approximately 10
seconds after releasing the switch lever.
►
Fig.4:
1.
Bottom lamp
NOTE:
When the tool is overheated, the bottom lamp
blinks for one minute. In this case, cool down the tool
before operating again.
NOTE:
Use a dry cloth to wipe the dirt off the lens of
the bottom lamp. Be careful not to scratch the lens of
the bottom lamp, or it may lower the illumination.
Low battery warning
When the remaining battery capacity of even one of
the two batteries becomes low, the power indicator
lamp blinks in red. Charge the batteries or replace the
charged batteries. When the remaining battery capacity
becomes much lower, the power indicator lamp lights up
in red and the tool stops.
►
Fig.5:
1.
Power indicator lamp
Maintenance warning
When the cumulative operating time of the tool exceeds 45
hours, the maintenance indicator lamp blinks in red. After 50
hours have elapsed, the maintenance indicator lamp lights
up in red and the tool changes to the maintenance mode.
►
Fig.6:
1.
Maintenance indicator lamp
NOTE:
The maintenance mode is selectable. The tool
is initially set to the continuous operation mode.
NOTE:
The tool does not work during configuration of
the maintenance mode or during reset of the cumula-
tive operating time.
Setting the maintenance mode
The maintenance mode is selectable.
1.
Switch on the tool by pressing the power switch for 5
seconds while squeezing the switch lever. The main-
tenance indicator lamp blinks in red and the power
indicator lamp indicates the current maintenance mode.
2. Press the power switch to select the desired main
-
tenance mode.
Power indicator lamp
Maintenance mode
Green
Continuous operation
mode
Red
Automatic stop mdoe
►
Fig.7:
1.
Power indicator lamp
2.
Maintenance
indicator lamp
3. Complete the setting by removing the battery from
the tool or leaving the tool for approximately 5
minutes.
Содержание HM004G
