Makita EA3500S Скачать руководство пользователя страница 41

Страница: 41 / 44

Trouble shooting

Malfunction

System

Observation

Cause

Chain does not run

Chain brake

Engine runs

Chain brake actuated.

Engine does not start or

only with difficulty

Ignition system

Ignition spark

Malfunction in fuel supply system, compression

system, mechanical malfunction.

No ignition spark

STOP switch in position, fault or short-

circuit in the wiring, Spark plug cap or spark plug

defective.

Fuel supply

Fuel tank is filled

Combination switch in Choke position, carburetor

defective, suction head dirty, fuel line bent or

interrupted.

Compression

system

Inside

Cylinder base packing ring defective, radial

shaft packings defective, cylinder or piston rings

defective.

Outside

Spark plug does not seal.

Mechanical

malfunction

Starter does not engage

Spring in starter broken, broken parts inside the

engine.

Warm start difficulties

Carburetor

Fuel tank is filled

Ignition spark

Wrong carburetor adjustment.

Engine starts, but dies

immediately

Fuel supply

Fuel tank is filled

Wrong idling adjustment, suction head or

carburetor dirty.

Tank venting defective, fuel line interrupted,

cable defective, Combination switch defective.

Insufficient power

Several systems

may be involved

simultaneously

Engine is idling

Air filter dirty, wrong carburetor adjustment,

muffler clogged, exhaust channel in cylinder

clogged, spark arrester screen clogged.

No chain lubrication

Oil tank/pump

No oil on the chain

Oil tank empty.

Oil guide groove dirty.

Oil-pump adjusting screw incorrectly adjusted.

Содержание EA3500S













































Результаты поиска

Содержание EA3500S

Отзывы:

Похожие инструкции для EA3500S

Бренды по названию

Популярные бренды

Makita EA3500S, Руководство оператора и по безопасности

Результаты поиска

Содержание EA3500S

Отзывы:

Похожие инструкции для EA3500S

Бренды по названию

Популярные бренды