manualshive.com logo in svg

Makita EA3500S, Руководство оператора и по безопасности, Страница: 27 / 44

Поделиться
Скачать
Makita EA3500S Скачать руководство пользователя страница 27

27

Refuelling

FOLLOW THE SAFETY PRECAUTIONS!

Be careful and cautious when handling fuels.

The engine must be switched off!

Thoroughly clean the area around the caps, to prevent dirt 

from getting into the fuel or oil tank.

Unscrew the tank cap (use the universal wrench if necessary, 

see illustration) and fill tank with fuel mixture or saw chain 

oil up to the bottom edge of the filling neck. Be careful not to 

spill fuel or chain oil!

Screw on the tank cap 

by hand all the way.

Clean the tank cap and the area around the tank after 

refuelling.

Lubricating the chain                  

During operation there must always be sufficient chain 

oil in the chain-oil tank to provide good chain lubrication. 

At medium oil feed rate, the oil tank holds enough for one 

fuel tank’s worth of operation. During this procedure check 

whether there is enough the chain oil in the tank and refill if 

necessary. 

Do this only with the engine turned off! 

Screw 

on the tank

 

cap

 by hand all the way.

waste oil

NEVER USE WASTE OIL

Waste oil is very dangerous for the environment.

Waste oil contains high amounts of carcinogenic substances.

Residues in waste oil result in a high degree of wear and tear 

at the oil pump and the sawing device.

In case of damage caused by using waste oil or inappropriate 

chain oil the product guarantee will be null and void.

Your salesman will inform you about the use of chain oil.

AVOID SKIN AND EYE CONTACT

Mineral oil products degrease your skin. If your skin comes 

in contact with these substances repeatedly and for an 

extended period of time, it will desiccate. Various skin 

diseases may result. In addition, allergic reactions are known 

to occur.

Eyes can be irritated by contact with oil. If oil comes into your 

eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

Important note on bio-degradable chain oils

If you are not planning to use the saw again for an 

extended period of time, empty the oil tank and put in a 

small amount of regular engine oil (SAE 30), and then 

run the saw for a time. This is necessary to flush out all 

remaining bio-degradable oil from the oil tank, oil-feed 

system, chain and guide bar, as many such oils tend 

to leave sticky residues over time, which can cause 

damage to the oil pump or other parts.

The next time you use the saw, fill the tank with BIOTOP 

chain oil again. In case of damage caused by using waste 

oil or inappropriate chain oil the product guarantee will be 

null and void.

Your salesman will inform you about the use of chain oil.

chain oil

fuel/oil mixture

Содержание EA3500S













































Отзывы:

Нет отзывов