background image

The tool will automatically stop during operation if the tool 
and/or battery are placed under one of the following 
conditions: 

• 

Overloaded: 

The tool is operated in a manner that causes 
it to draw an abnormally high current. 
In this situation, release the trigger switch on 
the tool and stop the application that caused 
the tool to become overloaded. Then pull the 
trigger switch again to restart. 
If the tool does not start, the battery is 
overheated. In this situation, let the battery 
cool before pulling the trigger switch again. 

• 

Low battery voltage: 

The remaining battery capacity is too low and 
the tool will not operate. In this situation, 
remove and recharge the battery. 

Blade guard 

For all countries other than European countries 

1

 

 

011238 

When lowering the handle, the blade guard rises 
automatically. The guard is spring loaded so it returns to 
its original position when the cut is completed and the 
handle is raised. 

 

WARNING: 

• 

Never defeat or remove the blade guard or the 
spring which attaches to the guard.

 An exposed 

blade as a result of defeated guarding may result in 
serious personal injury during operation. 

In the interest of your personal safety, always maintain 
the blade guard in good condition. Any irregular 
operation of the blade guard should be corrected 
immediately. Check to assure spring loaded return action 
of guard. 

 

WARNING: 

• 

Never use the tool if the blade guard or spring 
are damaged, faulty or removed.

 Operation of 

the tool with a damaged, faulty or removed guard 
may result in serious personal injury. 

 
 
 
 

For European countries 

1

2

 

 

011267 

When lowering the handle, the blade guard A rises 
automatically. The blade guard B rises as it contacts a 
workpiece. The guards are spring loaded so it returns to 
its original position when the cut is completed and the 
handle is raised. 

 

WARNING: 

• 

Never defeat or remove the blade guard or the 
spring which attaches to the guard.

 An exposed 

blade as a result of defeated guarding may result in 
serious personal injury during operation. 

In the interest of your personal safety, always maintain 
each blade guard in good condition. Any irregular 
operation of the blade guards should be corrected 
immediately. Check to assure spring loaded return action 
of guards. 

 

WARNING: 

• 

Never use the tool if the blade guard or spring 
are damaged, faulty or removed.

 Operation of 

the tool with a damaged, faulty or removed guard 
may result in serious personal injury. 

If the see-through blade guard becomes dirty, or sawdust 
adheres to it in such a way that the blade and/or workpiece is 
no longer easily visible, remove the battery cartridge and clean 
the guard carefully with a damp cloth. Do not use solvents or 
any petroleum-based cleaners on the plastic guard because 
this may cause damage to the guard. 
If the blade guard becomes dirty and needs to be cleaned for 
proper operation follow the steps below: 
With the tool switched off and the battery cartridge removed, 
use the supplied hex wrench to loosen the hex socket bolt 
holding the center cover. Loosen the hex socket bolt by turning 
it counterclockwise and raise the blade guard and center cover. 

1

 

 

011239 

1. Blade guard 

1. Blade guard A 
2. Blade guard B 

1. Blade guard 

Содержание DLS713NZ





















Отзывы: