16
•
Lay crown molding with its broad back
(hidden) surface down on the turn base
with its CEILING CONTACT EDGE
against the guide fence on the saw.
•
The finished piece to be used will
always be on the LEFT side of the blade
after the cut has been made.
In the case of right bevel cut
M
ol
d
i
ng
posi
t
io
n
i
n
Fi
g
. A
Beve
l
ang
l
e
M
i
ter
ang
l
e
Fo
r
ou
t
si
de
co
rner
Fo
r
i
n
si
de
co
rner
52
/
3
8°
t
yp
e
4
5
°
t
yp
e
R
i
ght
3
1.6°
4
5
°
t
yp
e
R
i
ght
33
.9°
R
i
ght
30
°
52
/
3
8°
t
yp
e
L
eft
3
1.6°
L
eft
35
.
3
°
R
i
ght
35
.
3
°
R
i
ght
35
.
3
°
R
i
ght
3
1.6°
(1)
(
2
)
(
3
)
(4)
T
a
bl
e
(A)
006363
M
ol
d
i
ng
posi
t
io
n
i
n
Fi
g
. A
M
ol
d
i
ng
edge
aga
i
n
s
t
g
ui
de
fen
c
e
(1)
Fo
r
ou
t
si
de
co
rner
Fo
r
i
n
si
de
co
rner
Fi
n
is
hed
pi
e
c
e
(
2
)
(
3
)
(4)
T
a
bl
e
(
B
)
Fi
n
is
hed
pi
e
c
e
will b
e
o
n
the
L
eft
si
de
o
f
bl
ade
.
Fi
n
is
hed
pi
e
c
e
will b
e
o
n
the
R
i
ght
si
de
o
f
bl
ade
.
W
a
ll co
nta
c
t
edge
s
h
oul
d
b
e
aga
i
n
s
t
g
ui
de
fen
c
e
.
W
a
ll co
nta
c
t
edge
s
h
oul
d
b
e
aga
i
n
s
t
g
ui
de
fen
c
e
.
C
e
ili
ng
co
nta
c
t
edge
s
h
oul
d
b
e
aga
i
n
s
t
g
ui
de
fen
c
e
.
006364
Example:
In the case of cutting 52/38° type crown
molding for position (1) in Fig. A:
•
Tilt and secure bevel angle setting to
33.9° RIGHT.
•
Adjust and secure miter angle setting to
31.6° RIGHT.
•
Lay crown molding with its broad back
(hidden) surface down on the turn base
with its WALL CONTACT EDGE against
the guide fence on the saw.
•
The finished piece to be used will
always be on the RIGHT side of the
blade after the cut has been made.
7. Wood
facing
Use of wood facing helps to assure splinter-free
cuts in workpieces. Attach a wood facing to the
guide fence using the holes in the guide fence.
See the figure concerning the dimensions for a
suggested wood facing.
Over
1
5mm
(
5/
8
"
)
Over 420mm
(16
-
1
/2"
)
1
1
50mm-
6
0mm
(
2"-2-3/
8
"
)
27mm
(1
-
1
/
16
"
)
8
5mm
(
3-3/
8
"
)
70mm
(
2-3/4"
)
8
5mm
(
3-3/
8
"
)
70mm
(
2-3/4"
)
002206
CAUTION:
•
Use the straight wood of even thickness as the
wood facing.
WARNING:
•
Use screws to attach the wood facing to the
guide fence. The screws should be installed
so that the screw heads are below the surface
of the wood facing so that they will not
interfere with the positioning of the material
being cut.
Misalignment of the material being cut
can case unexpected movement during the cutting
operation which may result in a loss of control and
serious personal injury.
NOTICE:
•
When the wood facing is attached, do not turn the
turn base with the handle lowered. The blade
and/or the wood facing will be damaged.
8. Cutting
repetitive
lengths
1
2
3
001846
When cutting several pieces of stock to the same
length, ranging from 220 mm to 385 mm, use of the
set plate (optional accessory) will facilitate more
efficient operation. Install the set plate on the holder
(optional accessory) as shown in the figure.
Align the cutting line on your workpiece with either the left
or right side of the groove in the kerf board, and while
holding the workpiece from moving, move the set plate
flush against the end of the workpiece. Then secure the
set plate with the screw. When the set plate is not used,
loosen the screw and turn the set plate out of the way.
NOTE:
•
Use of the holder-rod assembly (optional
accessory) allows cutting repetitive lengths up to
2,200 mm approximately.
1. Set plate
2. Holder
3. Screw
1. Holes
Содержание DLS713NZ
Страница 20: ...20 Makita Corporation www makita com 885295A4 ...