manualshive.com logo in svg

Majestic PEARL36STIN, Руководство по установке

Поделиться
Скачать
Majestic PEARL36STIN Скачать руководство пользователя страница 65

65

Majestic  •  PEARL36STIN, PEARL36PRIN Installation Manual  •  2478-980 Rev. C  •  3/17

Figure  10.  Log #8 Installed

Figure  11.  Log #9 Installed

LOG PIN

LOG PIN

LOG PIN

LOG PIN

P

IL

O

T

 S

ID

E

PILOT SIDE

PILOT SIDE

PILOT SIDE

8

8

99

Log #8 (SRV2478-708):  

Place Log #8 against the log pin and on the 

fl

 at spot of 

Log #7 as shown in Figure 10.   Note that the burnt end of 
the log is positioned in the center of the appliance.

Log #9 (SRV2272-709):  

Place Log #9 against the log pin and on the 

fl

 at spot of 

Log #4 as shown in Figure 10.   See Figure 7 for location 
of 

fl

 at spot.  

LOG TOUCHES LOG #7

LOG TOUCHES LOG #7

44

77

77

Figure  12.  Lava Rock and Ember Placement

Lava Rock and Glowing Embers

Place lava rock and glowing embers as shown in Figure 12.

WARNING! Risk of Explosion! Follow ember placement in-
structions in manual. DO NOT place embers directly over 
burner ports. Replace ember material annually. Improperly 
placed embers interfere with proper burner operation.

Placing the Ember Material

Ember material is shipped with this gas appliance. To place 
the ember material:

•   Embers may only be placed in areas as shown in Figure 

12. Care should be taken not to cover the lighting trail of 
ports near pilot assembly as shown in Figure 12. 

•  When placing Glowing Embers

®

 onto the burner, care 

should be taken so that the ports are not covered. Place 
the dime-size ember pieces.  See Figure 12.   Failure to 
follow this procedure will likely cause lighting and sooting 
problems.

•  Place Lava Rock on areas of base pan away from the 

burner. Use this material to give the appliance a realistic 
ash bed.

•  Save the remaining ember materials for use during 

appliance servicing. The embers provided should be 
enough for 3 to 5 applications.

BURNT END

BURNT END

= LAVA ROCK
= EMBERS

= NO EMBERS IN THIS AREA
= LOG PLACEMENT PINS
Do not cover log placement pins 
with lava rock or glowing embers.

Содержание PEARL36STIN
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды