Majestic PEARL36STIN Скачать руководство пользователя страница 57

Страница: 57 / 79

Majestic • PEARL36STIN, PEARL36PRIN Installation Manual • 2478-980 Rev. C • 3/17

A. Remove Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle

xed glass

assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate

replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

Appliance Setup

Figure 11.1 Fixed Glass Assembly

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath

the

rebox.

• The splatter guard is a piece of corrugated material

used to protect the appliance during the installation
process before

nishing work on the whole hearth is

complete. Splatter guards may be factory installed
or accompany the decorative front of the appliance,
depending on the

replace model. Splatter guards

must be removed before appliance is

red.

WARNING! Risk of Fire!

Close the ball valve before in-

stalling the splatter guard to prevent accidental lighting.
Remove the splatter guard before lighting the appliance.

Removing Fixed Glass Assembly

• Pull the four glass latches out of the grooves on the glass

frame top and bottom.

• Remove the glass door from the appliance.
• Multiple sides may be able to be removed based upon

model.

Replacing Fixed Glass Assembly

• Replace the glass door on the appliance.
• Pull out the four glass latches and place in the grooves

on the glass frame top and bottom.

• Make sure all sides are replaced properly.

LATCHES

BOTH BOTTOM

AND TOP)

GLASS

ASSEMBLY

To install the Splatter Guard:

Step 2. Crease

ap on top side of splatter guard using

the scored line as the guide. See Figure 11.3.

Figure 11.3

Step 1. Turn off gas to valve. Red gas shutoff knob is
located on ball valve. Disconnect the 6 volt transformer
from the junction box. See Figure 11.2

Figure 11.2

Содержание PEARL36STIN
















































































Результаты поиска

Содержание PEARL36STIN

Отзывы:

Бренды по названию

Популярные бренды

Majestic PEARL36STIN, Руководство по установке

Результаты поиска

Содержание PEARL36STIN

Отзывы:

Бренды по названию

Популярные бренды