Majestic PEARL36STIN Скачать руководство пользователя страница 35

Страница: 35 / 79

Majestic • PEARL36STIN, PEARL36PRIN Installation Manual • 2478-980 Rev. C • 3/17

CAUTION! Risk of Cuts, Abrasions or Flying Debris.

Wear protective gloves and safety glasses during instal-
lation. Sheet metal edges are sharp.

NOTICE:

Once appliance is set up for top or rear venting,

it CANNOT be changed at a later time.

A. Vent Collar Preparation

Appliance Preparation

Top Vent

Figure 6.3

Cut the metal retaining band and fold the sides out.

Figure 6.5

Remove and discard the seal cap, insulation

donut, insulation plug, and the insulation basket. Attach
the

rst vent section (it will snap into place). Slide the vent

gasket onto the vent section and then, up against the ap-
pliance. Secure the vent gasket to the appliance with two
self-tapping screws found in the manual bag. Note: The
vent gasket can found in the manual bag.

Proceed to Section 6.B.

Figure 6.2 PEARL36STIN Only:

Fold heat shield back

and secure with screw.

Figure 6.4

Fold the center parts of the retaining band up

and use to remove the vent cap.

Figure 6.1

PEARL36STIN Only:

Remove screws from

top heat shield.

TOP HEAT SHIELD

TOP HEAT SHIELD
REMOVE SCREWS

REMOVE SCREWS

FOLD HEAT SHIELD BACK

SECURE WITH SCREW

Содержание PEARL36STIN
















































































Результаты поиска

Содержание PEARL36STIN

Отзывы:

Бренды по названию

Популярные бренды

Majestic PEARL36STIN, Руководство по установке

Результаты поиска

Содержание PEARL36STIN

Отзывы:

Бренды по названию

Популярные бренды