manualshive.com logo in svg

Majestic PEARL36STIN, Руководство по установке

Поделиться
Скачать
Majestic PEARL36STIN Скачать руководство пользователя страница 46

46

Majestic  •  PEARL36STIN, PEARL36PRIN Installation Manual  •  2478-980 Rev. C  •  3/17

 

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

 wire 

110-120 VAC to the valve or to the appliance wall switch. 
Incorrect wiring will damage controls.

NOTICE: 

This appliance must be electrically wired 

and grounded in accordance with local codes or, in the 
absence of local codes, with 

National Electric Code 

ANSI/NFPA 70-latest edition

 or the 

Canadian Electric 

Code CSA C22.1.

•  Wire the appliance junction box to unswitched 110-

120 VAC. This is required for proper operation of the 
appliance.

•  A 110-120 VAC circuit for this product must be protected 

with ground-fault circuit-interrupter protection, in 
compliance with the applicable electrical codes, when 
it is installed in locations such as in bathrooms or near 
sinks.

•  Low voltage and 110-120 VAC voltage cannot be shared 

within the same wall box.

8 

8 

Electrical Information 

ROMEX CONNECTORS

Figure 8.1  Junction Box Detail

NOTICE: DO NOT

 wire 110-120 VAC to wall switch.

Junction Box Installation

The junction box must be wired from the 

INSIDE

 of the 

appliance:
•  Determine which side of the appliance the junction box 

is located on.

•  Pull the electrical wires from outside the appliance through 

the knockout making sure to use a Romex connector to 
fasten the electrical wires to the unit.

•  Pull enough wire into the valve compartment to easily reach 

the junction box location.

•  Remove the screw attaching the junction box to the junction 

box bracket and set it aside.

•  Route the wire through the knockout in the junction box 

bracket.

•  Wire the junction box and reattach it to the bracket by 

inserting the tab in the slot and attaching with screw 
previously removed.  Ensure that a Romex connector is 
used to attach the electrical wires to the junction box.

Содержание PEARL36STIN
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды