Majestic MARQUIS MARQ36IN-B Скачать руководство пользователя

Страница: 1 / 69

Majestic MARQ36IN-B, MARQ42IN-B Installation Manual • 2614-980 Rev. D • 4/19

Installation Manual

Installation and Appliance Setup

NOTICE: DO NOT

discard this manual!

This appliance may be installed as an OEM

installation in manufactured home (USA

only) or mobile home and must be installed

in accordance with the manufacturer’s

instructions and the

Manufactured Home

Construction and Safety Standard,

Title 24

CFR, Part 3280

in the United States, or the

Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series,

in Canada.

This appliance is only for use with the type(s)

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gases, unless a certified kit is used.

DANGER

HOT GLASS

WILL

CAUSE BURNS.

DO NOT TOUCH

GLASS

UNTIL COOLED.

NEVER

ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided

with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

•

DO NOT

store or use gasoline or other flam

mable vapors and liquids in the vicinity of this

or any other appliance.

• What to do if you smell gas

DO NOT

try to light any appliance.

DO NOT

touch any electrical switch.

NOT

use any phone in your building.

- Leave the building immediately.
- Immediately call your gas supplier from

a neighbor’s phone. Follow the gas sup-

plier’s instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed

by a qualified installer, service agency, or the

gas supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

Models:

MARQ36IN-B, MARQ42IN-B

MARQUIS

SERIES

CAUTION! Risk of Fire! DO NOT

store instruction manuals inside fireplace cavity.

High temperatures could cause a fire.

INSTALLER: Leave this manual with the appliance, not inside the appliance.

CONSUMER: Retain this manual for future reference. Do not store inside the appliance.

Decorative barrier front provided with this appliance.

Содержание MARQUIS MARQ36IN-B






































































Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды

Majestic MARQUIS MARQ36IN-B, Руководство по установке

Результаты поиска

Содержание MARQUIS MARQ36IN-B

Отзывы:

Похожие инструкции для MARQUIS MARQ36IN-B

Бренды по названию

Популярные бренды