MAGUIRE Weigh Scale Blender, Руководство по эксплуатации и техническому обслуживанию

Страница: 39 / 81

39
FAST This key will allow you to exceed the normal blending rate of your unit. Once your system has learned
proper flow rates of each material, the timing of each component dispense is very consistent cycle to
cycle. The FAST key allows one or more FAST REPEAT cycles to follow a normal calibrated cycle. In a
FAST REPEAT cycle all components are dispensed simultaneously, without any weights being taken.
Errors in dispense amounts will not be detected. These are, in fact, volumetric dispenses, not gravimetric.
These dispenses take much less time. Throughput is easily doubled in this manner.
This key is NOT FUNCTIONAL unless the 4th digit of the "FLG" parameter is set to 1 (xxx1x). To do this,
see the SOFTWARE MAINTENANCE section, PARAMETER TABLE, "FLG".
The shorter mixing time may be a problem. So the number of FAST REPEAT cycles is kept as low as
possible. Up to 4 repeats may occur.
Press the FAST key to toggle the FAST flag ON of OFF. When set to (FAST OFF) the FAST mode will
not operate. When set to (FAST ON) every normal calibrated dispense will be followed by up to 4 FAST
repeat dispenses.
This series of 4 dispenses is terminated as soon as the sensor is covered, which indicates the blender has
"caught up". The next cycle will then be a weighed cycle, followed by the required series of fast cycles to
catch up again.
Press * to toggle between (FAST ON) and (FAST OFF).
Press EXIT, to exit.
When the FAST mode is in operation, the display ( FAST) will flash intermittently.
SETTING Press once and the current setting of component 1 is displayed. Display will say (1 X xx.x). X is material
type, either R, (REGRIND); N, (NATURAL); or A, (ADDITIVE). xx.x is the current setting.
Press SET to step forward through all the settings.
Press * key to backup in the list.
NEW settings may be entered directly.
REGRIND and ADDITIVE settings are expressed as percents, up to 99.9 percent. NATURAL is any
number you wish (usually weight). It is used to establish RATIOS with all other NATURAL entries. When
only one material is designated as a NATURAL, the value of it's setting has no meaning, except that it
must be set to some value to operate.
If you wish to restrict the entry of settings to the PROGRAM mode only, (password required), you may do
so by altering the _SE parameter for each component that you wish to "lock out". See MAINTENANCE
SECTION, PARAMETERS, _SE parameter.
TAG This key allows two pieces of information to be "tagged" onto all data that is either printed or retrieved
through the computer port. The items are WORK ORDER number and OPERATOR number.
This key is NOT FUNCTIONAL unless the 2nd digit of the "FLG" parameter is set to 1 (x1xxx). To do this,
see the SOFTWARE MAINTENANCE section, PARAMETER TABLE, "FLG".
Press once to display the current Work Order number (WO-----). Press again to display the current
Operator number (OPRTR---). Press again for the Recipe (RECP ---). You may enter or change the Work
Order or Operator number, when each is displayed, but not the recipe number.
These numbers are for your TRACKING of information ONLY. They have NO EFFECT on the operation of
the Weigh Scale Blender.
•
WORK ORDER number (6 digits) allows you to tag all information with an internal accounting number
such as a job or purchase order number.
•
OPERATOR number (3 digits) allows you to track who is operating the equipment.
•
RECIPE number (3 digits) allows you to track what recipe you are using but you cannot enter or
change it here. The number will be a 2-digit number if a recipe is being run that resides in the
controller RAM; one that was entered using the RECIPE key. If a recipe has been entered using our
MLAN software, through the computer port, then a 3-digit number will be displayed. In either case,
the number in this field will be displayed and "tagged" to all printouts and retrievals.
EXIT will exit the sequence at any point.