background image

 

iv

FCC WARNING STATEMENT 

 
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant 
to Part 15 of FCC Rules.  These limits are designed to provide reasonable protection against harmful 
interference when the equipment is operated in a commercial environment.  This equipment generates, 
uses, and can radiate radio frequency energy and, if not installed and used in accordance with  the 
instruction manual, may cause harmful interference to radio communications.  Operation of this 
equipment in a residential area is likely to cause harmful interference in which case the user will be 
required to correct the interference at his own expense. 

 

FCC COMPLIANCE STATEMENT 

 
This device complies with Part 15 of the FCC Rules.  Operation of this device is subject to the following 
two conditions: (1) This device may not cause harmful interference. And (2) This device must accept any 
interference received, including interference that may cause undesired operation. 

 

CANADIAN DOC STATEMENT 

 

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out in 
the Radio Interference Regulations of the Canadian Department of Communications. 
 
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux 
appareils numériques de las classe A prescrites dans le Réglement sur le brouillage radioélectrique édicté 
par les ministère des Communications du Canada. 

 

CE STANDARDS

 

 
Testing for compliance to CE and FCC requirements was performed by an independent laboratory.  The 
unit under test was found compliant to Class A. 
 

UL/CSA 

 

This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950. 

 
 
 

Содержание MT-95























































Отзывы: