Magnetrol R82 Скачать руководство пользователя страница 34

Страница: 34 / 64

2.6.6.3 Radar Transmitter User Menu—Flow and Level (cont.)

Note: Press UP arrow 5 times to reach screen where menu language can be chosen.

58-610 Model R82 Radar Transmitter

Display

Action

Comment

Flow Setup

(continued from

previous page)

(continued on

next page)

Flow Element

Select one of the following primary Flow Elements that
are stored in the firmware:

Parshall

flume sizes of

12"

18"

24"

36"

48"

60"

72"

96"

120" and 144"

. Palmer-Bwls (Palmer-

Bowlus) flume sizes of

10"

12"

15", 18"

21"

24"

27"

and

30"

V-notch

weir sizes of

22.5°

30°

45°

60°

90° and 120°

. Rect with Ends (Rectangular Weir with

End Contractions), Rect w/o Ends (Rectangular Weir
without End Contractions), and Cipoletti weir.

Crest Length

The

Crest Length

screen only appears when the chosen

Flow Element

is Cipoletti or one of the

Rectangular

weirs.

Input this length in the user-selected level units.

Reference Dist

The

Reference Distance

is measured from the bottom of

the antenna threads to the point of zero flow in the weir
or flume. This must be measured very accurately in the
userselected level units. For some

Flow Elements

, such

Parshall

flumes, the

Reference Dist

is the same as the

Range

value. Weirs and some other Flow Elements will

have a

Reference Distance

that is shorter than the

Range

value.

Maximum Head

Maximum Head

is the highest liquid level (Head) value in

the flume or weir before the flow equation is no longer
valid. The

Maximum Head

is expressed in the user

selected

Level Units

. The R82 will default to the largest

Maximum Head

value that is allowed for any given flume

or weir. The

Maximum Head

value can be revised

depending on the value of the

Reference Distance

, or for

end user preference.

Maximum Flow

Maximum Flow

is a read-only value that represents the

flow value corresponding to the

Maximum Head

value for

the flume or weir.

Low Flow Cutoff

The

Low Flow Cutoff

(in user-selected level units) will

force the calculated flow value to zero whenever the
Head is below this point. This parameter will have a
default and minimum value of zero.

Totalizers: Units

The

Totalizer Units

screen is for selection of the units for

both the resettable and non-resettable totalizers. Select

Gallons

(factory default unit),

Mil Gallons

Liters

Mil Liters

Cubic Meters

, or

Cubic Feet

Totalizers: Total NR Mult

The

Total NR Mul

t screen allows selection of the multipli-

er to be used for the non-resettable totalizer. The function
of the totalizer multiplier is such that if the chosen units
are gallons and the multiplier is 100, the totalizer value
will increment one whole unit for each 100 gallons. Select

100

1,000

(default),

10,000

100,000

Totalizers: Totalizer NR

This is a read only screen that displays the present value
of the non-resettable totalizer.

Totalizers: Total NR Time

This is a read only screen that displays the time that has
elapsed since the non-resettable totalizer has been total-
izing flow.

Содержание R82

































































Результаты поиска

Содержание R82

Отзывы:

Похожие инструкции для R82

Бренды по названию

Популярные бренды

Magnetrol R82, Инструкция по установке и эксплуатации

Результаты поиска

Содержание R82

Отзывы:

Похожие инструкции для R82

Бренды по названию

Популярные бренды