Step 1: Component Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Step 2: 10-Pin Main Harness Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Step 3: 5-Pin Power Harness Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Step 4: Optional Accessory Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11
Step 5: Transmitter Coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13
Step 6: Remote Feature Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-16
Step 7: Multiple Car Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Step 8: General Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Step 9: Speciality Feature and Optional Equipment Testing . . . . . . . . . . . . . . . . . . . . . . 17-19
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Step 1: Component Installation
Mounting the Control Module:
Secure the alarm control module within the passenger’s compartment
of the vehicle. Never mount the alarm control module in the engine compartment or in the direct
path of the heater. Secure the alarm control module by using wire ties or with the screws provided.
Mounting the Siren:
Find a suitable location in the engine compartment to secure the siren that
provides a direct sound path to the ground. Use the self tapping screws provided. Connect the
black wire coming from the siren to the frame of the vehicle. Route the brown wire through the
firewall to the location of the alarm control module.
Installing Hood/Trunk Pin Switches:
To install the switch either in the truck or under the hood, find
a suitable location where the switch will make contact with the hood or trunk lid and will not get
wet. Use the bracket provided or drill a 1/4” hole in the desired location.
Mounting the LED Status Indicator:
Find a suitable location for the LED and drill a 5/16” hole in the
desired location. Feed the 2-pin plug through the hole and press the body of the LED into place.
Run the LED wires to the location of the alarm control module.
2
Step 2: 10-Pin Main Harness Installation
The main wire harness contains 8 wires which all have a specific purpose. Follow the wiring
recommendations enclosed for each wire. Wires not used should be released from the harness
connector or taped off to prevent accidental shorting. Included with the 10-pin wire harness are two
loose wires, an orange wire and a white wire with black stripe. See main harness and power harness
wiring instructions for these two loose wires.
Warning!
Do not plug the 10-pin or 5-pin wire harness into the alarm control module before you
begin installing the alarm. The wire harnesses must be plugged into the alarm control module
after all connections are made. Failure to follow this procedure could cause some confusion with
transmitter operation and or alarm function operation.
Vacant Sockets
Main Harness
First Vacant Socket (Located in the 1st Position)
Second Vacant Socket (Located in the 8th Position)
Index
