background image

       1-800-MAGLINE (624-5463) 

 

 

 Page 6                                               www.magliner.com

CooLift

®

CTA43 BULK HEAD REMOVAL

TOOLS NEEDED:

7/16” WRENCH, 1/2” WRENCH, #3 PHILLIPS SCREWDRIVER, #4 PHILLIPS SCREWDRIVER

SPACER BLOCK (4” x 4” x 24” WOODEN BLOCK)

Note:  It is important to keep the CooLift upright at all times.

1) 

Place the CooLift on a level flooring surface with the holding brake engaged.

2)  Raise the deck to the highest position.
3)  Place a spacer block between the deck and the base of the cart.

4)  Turn off main power switch.

5)  Remove the two screws (I) that attach the bulk head (A) to the base plate using the #4 Phillips 

screwdriver and the 1/2” wrench.

6)  Take out the four screws (G) that attach the bulk head saddle plate (B) and the load retaining strap 

assembly and spacer (C, D) to the bulk head and the main cart using the #3 Phillips screwdriver 
and the 7/16” wrench.

     

NOTE: If the bulk head is going to be reinstalled after servicing, only the two screws (G)

   

     anchored to the main cart and the saddle plate need to be removed.  If the bulk head is 

taken off and the CooLift will be used in the 53” pallet configuration, a new saddle plate 

(309151) will need to be installed.

7)  Lift and remove the saddle plate.  Then lift and remove the bulk head frame to disengage from the 

base plate.

CTA43 BULK HEAD INSTALLATION

TOOLS NEEDED:

7/16” WRENCH, 1/2” WRENCH, #3 PHILLIPS SCREWDRIVER, #4 PHILLIPS SCREWDRIVER

SPACER BLOCK (4” x 4” x 24” WOODEN BLOCK)

Note:  It is important to keep the CooLift upright at all times.

1) 

Place the CooLift on a level flooring surface with the holding brake engaged.

2)  Raise the deck to the highest position.
3)  Insert a spacer block between the deck and the base of the cart.

4)  Turn off main power switch.

5)  Slide the bulk head (A) into position on the bulk head mounts located on the base plate.
6)  Place the bulk head saddle plate (B) into position with the containment strap assembly and strap 

spacer (C, D) above it and attach using the four screws (G) and lock nuts (H) and finger tighten.

7)  Attach the bulk head to the mounts on the base plate using the two screws (I) and securely tighten 

them to the lock nuts (J) using the #4 Phillips screwdriver and the 1/2” wrench.

8)  Securely tighten the four screws (G) in the bulk head saddle plate (B) using the #3 Phillips 

screwdriver and the 7/16” wrench.

Содержание CooLift CTA43

































































Отзывы: