MacDonald Steel Limited HDP Deluxe DFC4 Скачать руководство пользователя страница 3

Страница: 3 / 29

MacDonald Steel Limited

BREWERY SYSTEMS DIVISION

REV 00

FEATURES

•

Independent stations, fills one to four bottles

•

Auto level detection, with adjustable fill heights

•

Analog pressure switch control: easy setup of vacuum draw and fobbing

•

Selectable number of evacuation cycles.

•

Auto and manual crowning

•

Monitoring of the fill sequence for easy troubleshooting

•

Preprogrammed cleaning cycles (CIP)

•

Operator interface: 8” color touch screen for setup, cleaning and troubleshooting

•

Adapters are available for filling cans and various size bottles

•

Fill from top nozzles available as an alternative to fill from bottom

OPERATING REQUIREMENTS

Clean dry air: 90 psi @ 2.5 CFM (min. 3/8” supply line) with necessary adaptor. Oil free recommended.

Potable water supply: warm and cold;

max temperature 70°F or 21°C

C02 at 50 PSI max (3/8” supply line)

120 or 220 VAC, 50-60Hz, 4 AMP, according to local supply.

Surge suppression power bar is

recommended.

Beer supply line to fit sanitary fitting

1/4” line to drain (supplied)

5 gallon (min) pressurized keg for cleaning or other pressurized source

Содержание HDP Deluxe DFC4






























Результаты поиска

Содержание HDP Deluxe DFC4

Отзывы:

Бренды по названию

Популярные бренды

MacDonald Steel Limited HDP Deluxe DFC4, Руководство пользователя

Результаты поиска

Содержание HDP Deluxe DFC4

Отзывы:

Бренды по названию

Популярные бренды