MacDon D60 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 35

MacDon D60 Скачать руководство пользователя страница 10

10

INSTALLATION

MECHANICAL FITMENT

These instructions refer to the diagram attached titled

Mechanical Fitment Diagram

, use for

reference upon installation.

Refer to the attached drawing UCA-MCD-ASM as support to the detailed instructions for
further information.

Note:

•

Installation process is minimum a two-person task.

•

Ensure the header front is detached from the header and resting on
a flat stable surface for accessibility and safety during installation.

•

Place boards over draper belt in locations requiring access for
installation, to protect the belts from damage and provide a stable
surface.

MOUNT BRACKETRY
STEP

INSTRUCTION

REFERENCE IMAGE

1

Mark locations of fixture points on
the header front for Parts 1B, 2B, 8
and 9, as per attached drawing UCA-
MCD-ASM.
Bracket mounts, Parts 1B and 2B may
be preexisting on header front. If
preexisting, conduct a dimensional
check, to ensure the bracketry
spacing is correct as per the attached
drawing.

2

Align base plates of Parts 8 and 9 to
the flat plate profile of the header
front, on the marked locations
(centered to the

‘fore and aft’

,

forwards and rearwards linear
motion actuators), as depicted in
drawing UCA-MCD-ASM.
Mark out plate profiles.

«
...
8
9
10
11
12
...
»

Содержание D60




































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды