MacDon C Series Скачать руководство пользователя страница 32

Страница: 32 / 70

Setup procedure and adjustment of the corn head

8 Setup procedure and adjustment of the corn head

8.1 Frame

The included parking stands must be always used

before the machine is disconnected from the com-

bine. Adjust the parking stand position in a way that

the distance between the ground and the lower

support of the corn head is about 30 cm. The stand

can be moved after the removal of the retaining pin.

8.2 Gathering auger

The gathering auger is driven through a torque-limiting clutch that can disengage

the drive on excessive loads. This clutch is located on the left-hand side, but an ad-

ditional clutch is located on the right hand side in the case of 12-row corn heads.

In some conditions it may be necessary to change the speed of the gathering auger.

An additional sprocket is available to permit changing the auger speed to match

field conditions.

Parts of the gathering auger height adjuster:

1. Chain drive connecting link

2. Adjusting plate nuts

3. Auger raising/lowering with M12 nuts

4. Chain tensioner setting

5. Chain guidance

6. Auger fore/aft adjusting bolt

Fix frame header: for adjusting the auger use the following screws - no. 3 and no. 6.

Folding header: the auger cannot be adjusted!

Содержание C Series







































































Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды

MacDon C Series, Руководство оператора

Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды