MacDon C Series Скачать руководство пользователя страница 7

Страница: 7 / 70

Safety

a. Before beginning any maintenance or lubricating, stop the

engine of the combine and remove the key!

1.326.703

b. If you stop the combine while the header is lifted, secure the

loose working cylinder with the help of the device - dive in-

hibitor - fixed to the hydraulic working cylinder of the com-

bine to avoid the accidental crash of the header.

1.326.701

c. Always stay clear of moving elements during operation! Al-

ways disengage header drive, shut off the engine and re-

move key before servicing or unclogging header.

1.315.438

d. Always keep your distance from the rotating parts of the

machine. The header’s snapping rolls and other moving

parts can’t be covered completely due to their functions. Do

not feed crop material into machine by hand or attempt to

manually unplug machine while it is running. The stalk rolls

can feed the crop material in faster than you can release

your grip on it. To avoid personal injury or mortal accident

always stop engine before unclogging.

1.326.702

e. Never attempt to open or remove shield while the engine is

running. Keep every shield in its place. Avoid direct contact

of your hand, leg, any part of your body or cloth with rotat-

ing, moving machine parts, elements! Before approaching

any moving parts wait for them to completely stop!

1.326.705 1.326.704

Содержание C Series







































































Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды

MacDon C Series, Руководство оператора

Результаты поиска

Содержание C Series

Отзывы:

Похожие инструкции для C Series

Бренды по названию

Популярные бренды