MacDon C Series Скачать руководство пользователя страница 23

Страница: 23 / 70

Mounting the corn head on the combine

6.1.8 ACROS

Mounting the corn head to the feeder house:

1. Preparing the feeder house for mounting the corn head.

1.1. Remove the frame and the spacer with the drop-in roll from the feeder

house.

1.2. Loosen the blocks on the bottom spring, remove the side spring blocks with

faders. Also remove the two springs which are above the feeder house.

1.3. Lift the lower drive shaft on the feeder house, freeing the lower supporting

and fixed.

1.4. Unscrew the

16 - bolts until the cotter pin collision. Remove the

12 bolts.

Turn the supports to be coincident with the threaded holes with the opening

of the side panel, insert the

12 bolt and screw it in until it stops. Tighten the

M16 bolt until it stops. Released the feeder house lower drive shafts fixation.

1.5. Mount the spacer (1) with fixed finger on the feeder house, and tighten the

removed screws.

1.6. Mount the two faders on the right and left of the feeder houses console with

a cotter pin (5) to the shaft (4).

1.7. On the feeder house’s right side front axle remove the z=18 pinion and

mount the z=16 pinion on. Re-

move the transit link in the

chain and mount the drop-in

drive chain in its place. The

chain contour must be in plane

and adjust the chain tension.

2. Prepare the corn head for mounting

on the feeder house.

The isolation plate (3) should be

turned, so that it won't hang out from

the corn heads side plate.

3. Mounting corn head on the feeder

house.

Lower the feeder house so that the,

spacers(1) hook pin (6) is lower than

Содержание C Series







































































Результаты поиска

Содержание C Series

Отзывы:

Бренды по названию

Популярные бренды

MacDon C Series, Руководство оператора

Результаты поиска

Содержание C Series

Отзывы:

Бренды по названию

Популярные бренды