MacDon C Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 70

background image

Shipping conditions

16

5 Shipping conditions

All your delivered corn heads are filled with oil, and are mounted on a shipping skid.

Check the lubricant level before you take over the corn head!

WARNING!

The corn head can be lifted with a suitable crane and fork lift.

When you choose the elevating equipment you should consider

the weight detailed.

When elevating with fork lift the corn head becomes movable if placing the elevating

forks under the metal delivery support under the machine. Be careful to place the

elevating forks symmetrically to the central line of the machine. The exact place of

elevating points is shown by the label on the illustration.

When elevating with crane the elevating cable is to be fixed in the elevator retainers

situated on the elevator strip clamping mounted on the skid plate of snapping units.

The elevator points are signed with the label on the strip clamping.

When you elevate with crane the cable angle should be max. 90° (according to the

illustration).

The minimum "l" cable length for keeping the max. 90° angle:

The 6-8-row fix and foldable machines: 2150 mm

The 12-row fix and foldable machines 11250 mm (in case of 4 pieces of cables)

«
...
15
16
17
18
19
...
»

Содержание C Series







































































Отзывы:

Нет отзывов

Похожие инструкции для C Series

Бренд: DARAY Страницы: 28

Бренд: MacDon Страницы: 88

Бренд: Jiffy Страницы: 15

Бренд: Baoding Longer Precision Pump Страницы: 6

Бренд: Handler Страницы: 25

Бренд: Wahl Страницы: 47

Бренд: RayLight Страницы: 34

GAZELLE FREESTYLE

Бренд: Gazelle Страницы: 10

Бренд: Latham Страницы: 19

Бренд: Parkside Страницы: 95

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: quadient Страницы: 188

Бренд: Radarsign Страницы: 16

Бренд: YOKOGAWA Страницы: 75

Бренд: ABB Страницы: 33

Exitronix LEMD Series

Бренд: BARRON Страницы: 6

Бренд: Landoll Страницы: 144

Бренд: Castellini Страницы: 299

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды