MacDon C Series Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 70

background image

Mounting the corn head on the combine

24

7. Remove the chain on the right side of the feeder house (9).

8. From the beater (10) remove the safety switch (11) and the holding clamps.

9. From the feeder house frame remove the cover plate (12).

10. From the feeder house right side remove the beater’s (10) bracket (13).

11. Holding the beater, unscrew the 3-3 bolts on the left and right (14; 15) which are

holding the bearing house.

12. Remove the beaters (10) with the bearing house (16; 17) from the feeder houses

frame.

13. On the removed grain beaters place (10) mount the corn beater fingers (18),

together with the protective plates (19; 20).

14. Mount the bracket on the right side of the feeder house (21).

15. Mount on the feeder houses right side 2 bolts (14), which had previously been

removed, along with the protective plates (19; 20).

16. On the corn beaters mount the previously removed bracket (13).

17. The corn feeder has to be installed in the bearing housing in a way that the

beaters during rotation cannot reach the feeder house.

18. Mount the previously removed safety clutch and chain (9; 11).

19. Mount the previously removed safety plate (12).

20. Lift the frame (6) and lock it with the hooks (1).

21. Connect back to the frame the tension rods (7; 8), and the springs (5).

22. Tension the spring tensioners (2; 3; 4) by the measured dimensions.

«
...
23
24
25
26
27
...
»

Содержание C Series







































































Отзывы:

Нет отзывов

Похожие инструкции для C Series

Бренд: iGuzzini Страницы: 20

Бренд: GE Страницы: 138

Бренд: Tabi Страницы: 8

Бренд: Dabi Atlante Страницы: 102

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: iFIT Страницы: 11

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: Safety 1st Страницы: 4

Бренд: Safety Engineering Страницы: 5

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренд: Teac Страницы: 76

Бренд: Teac Страницы: 3

Бренд: Teac Страницы: 50

Бренд: Teagle Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды