LYNXTechnik C MX 5710 Скачать руководство пользователя

Страница: 1 / 36

LYNX

Technik

Broadcast Television Equipment

Reference Manual

C MX 5710

HD/SD Analog Video to SDI Converter with Frame Synchronizer,

Analog Audio Inputs and AES Ports

Revision 1.0

– July 2015

This Manual Supports Device Revisions:

C MX 5710 Firmware Revision

688

Control System GUI Release

8.4.0

Information in this document is subject to change without notice. No part of this document may be reproduced or

transmitted in any form or by any means, electronic or mechanical for any purpose, without express written permission of

LYNX Technik AG.

LYNX Technik AG may have patents, patent applications, trademarks, copyrights or other intellectual property rights

covering the subject matter in this document. Except as expressly written by LYNX Technik AG, the furnishing of this

document does not give you any license to patents, trademarks, copyrights or other intellectual property of LYNX Technik

AG or any of its affiliates.

LYNX Technik AG

Brunnenweg 3

D 64331 Weiterstadt

Germany

www.lynx-technik.com

Содержание C MX 5710





































Результаты поиска

Содержание C MX 5710

Отзывы:

Похожие инструкции для C MX 5710

Бренды по названию

Популярные бренды

LYNXTechnik C MX 5710, Справочное руководство

Результаты поиска

Содержание C MX 5710

Отзывы:

Похожие инструкции для C MX 5710

Бренды по названию

Популярные бренды