Serena
TM
Manual Cellular Shade
Installation Guide (please read before installing)
English
A.1
Step 1: Review Included Components
Before you begin, open the box and
make sure you have all the necessary
parts: the shade, mounting brackets,
and screws.
You will also need a cordless drill, a
3/32 inch drill bit, a #2 Phillips bit, a
pencil, and a tape measure.
Mounting
brackets
Cellular shade
#6 Phillips
mounting
screws
Included:
Tools required:
Option A: Inside Mount
Hold the shade up to the window to make sure
it’s the correct size.
A.2
* NOTE: Shades wider than 45 inches
(vinyl headrail) or 48 inches (aluminum
headrail) will need a third bracket (
3
)
(included). Install this bracket in the
center of the shade.
(continued)
A.4
Install the mounting brackets,
using the provided screws. Using
the cordless drill, drive each screw
through the holes in the top of
the bracket.
*
2 in
2 in
A.5
Install the shade in the brackets.
Holding the shade in both hands,
tilt the top of the shade slightly away
from you and hook the front edge
into the brackets. Then gently
tilt the shade down and press the
bottom of the headrail until you hear
it click into place.
Side view
Click
e
e
Option B: Outside Mount On Trim
B.1
Hold the shade up to the window to make sure it’s the
correct size. Center the shade and mark the trim at each
end of the shade.
B.2
*
2 in
2 in
Mark the center line for the two
outside brackets, 2 inches in from
each side of the window.
Mark the center line for the two
outside brackets, 2 inches in from
the marks you made in step B.1.
Side view
Bracket
Window frame
A.3
Center the bracket on the center line
and align it with the front edge of the
window trim. Mark hole locations and
then pre-drill holes for the screws.
(Repeat for all brackets.)
B.4
Install the mounting brackets using the
provided screws. Place each bracket
fl ush against the trim (using spacers*
behind brackets if needed) and using
the cordless drill, drive each screw
through the holes in the bracket.
B.3
Align the top of the brackets with the
top of the trim and the center line.
Mark the hole locations and then
pre-drill holes for the screws.
Side view
Bracket Spacer*
Wall
Window
trim
Step 2: Installing Mounting Brackets
Your shade was manufactured according to the mounting option you chose when
ordering your shade. Make sure you follow the appropriate mounting instructions:
Opt. A
inside mount,
Opt. B
outside mount on trim, or
Opt. C
outside mount above trim.
1
2
3
Top view of shade wider than 45 inches
or 48 inches
* NOTE: Shades wider than 45 inches
(vinyl headrail) or 48 inches (aluminum
headrail) will need a third bracket (
3
)
(included). Install this bracket in the
center of the shade.
If the shade is wider than 72 inches,
you will need to install a third (
3
) and
a fourth bracket (
4
) (included). Install
each of these one-third of the way in
from the outer brackets.
* NOTE: If window trim is angled, or not level vertically, place an angled spacer (not
included) behind each bracket. Ensure that the shade is level before placing the
bracket fl ush against the trim. Pre-drill a hole through the spacer as well.
Top view of shade wider than 72 inches
Top view of shade wider than 45 inches
or 48 inches
Hook front edge
Press shade
Important:
Be sure not to catch any fabric cells in the brackets.
B.5
Refer to step A.5 to install the shade in the brackets.
Drill
Pencil
Tape measure
#2 Phillips drill bit
#2 Phillips screwdriver
3/32 inch drill bit
Top view of shade wider than 72 inches
1
2
3
4
1
/
3
1
/
3
1
/
3
If the shade is wider than 72 inches,
you will need to install a third (
3
)
and a fourth bracket (
4
) (included).
Install each of these one-third of the
way in from the outer brackets.
Important:
•
Make sure you are screwing into wood studs.
•
If you’re not mounting the brackets into wood studs, you’ll need to use appropriate
fasteners for the mounting surface (not included).
•
Make sure the brackets are aligned with each other. (If not, the shade may not
properly snap into the brackets.)
1
2
3
4
1
/
3
1
/
3
1
/
3
1
2
3
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
11/2013
P/N 045356 Rev. E
