Lutron Electronics seeTouch guestroom solutions, Руководство по установке

Страница: 10 / 21

10 seeTouch
®
guestroom solutions
Contact Closure Wiring
IO Connections
DIP switches
LED 1: CCO 1
LED 2: CCO 2
LED 3: CCO 3
LED 4: CCO 4
LED 5: CCO 5
LED 6: Unused
LED 7: Status
Notes: CCO LED is ON when CCO NO (normally
open contact) is closed.
Status LED blinks once per second
during normal operation
CCO and CCI connectors hold one
0,08 - 1,5 mm
2
(28 - 16 AWG) wire
NC = Normally closed
NO = Normally open
Data Link (to wallstations)
3: MUX
1: Common
4: MUX
CCO
1
NC
CCO
1
NO
1-2
COM
CCO
2
NC
CCO
2
NO
CCO
3
NC
CCO
3
NO
3-4
COM
CCO
4
NC
CCO
4
NO
CCO
5
NC
CCO
5
NO
5
COM
CCI
1
CCI
2
CCI
3
CCI
4
CCI
5
COM
Contact Closure Outputs Contact
Closure
Inputs
1 2 3 4 5 6 7
Program button
2: 24 V
DIP switches
LED 1: CCO 1
LED 2: CCO 2
LED 3: CCO 3
LED 4: CCO 4
LED 5: CCO 5
LED 6: Unused
LED 7: Status
Notes: CCO LED is ON when CCO NO (normally
open contact) is closed.
Status LED blinks once per second
during normal operation
CCO and CCI connectors hold one
0,08 - 1,5 mm
2
(28 - 16 AWG) wire
NC = Normally closed
NO = Normally open
Data Link (to wallstations)
3: MUX
1: Common
4: MUX
CCO
1
NC
CCO
1
NO
1-2
COM
CCO
2
NC
CCO
2
NO
CCO
3
NC
CCO
3
NO
3-4
COM
CCO
4
NC
CCO
4
NO
CCO
5
NC
CCO
5
NO
5
COM
CCI
1
CCI
2
CCI
3
CCI
4
CCI
5
COM
Contact Closure Outputs
Contact
Closure
Inputs
1 2 3 4 5 6 7
Program button
2: 24 V
Contact Closure Ratings
Five Input Terminals
• Accepts maintained inputs and momentary inputs with 40 ms
minimum pulse times.
• Off-state leakage current must be less than 100 μA.
• Open circuit voltage: 24 V maximum.
• Inputs must be dry contact closure, solid state, open collector,
or active-low (NPN)/active high (PNP) output.
– Open collector NPN or active-low on-state voltage must be
less than 2 V and sink 3,0 mA.
– Open collector PNP or active-high on-state voltage must be
greater than 12 V and source 3,0 mA.
• Lutron recommends a maximum of 3 occupant sensors wired
in parallel per input.
Five Output Terminals
• Provide selectable maintained or momentary (250 ms) outputs.
• The interface is not rated to control unclamped, inductive loads.
Inductive loads include, but are not limited to, relays, solenoids,
and motors. To control these types of equipment, a flyback
diode must be used (DC voltages only). See diagram below.
• Output relays are non-latching (i.e. if relays are closed and
power is lost, relays will open).
Supply
Voltage
0 – 24 V
0 – 24 V
Resistive
Load
1,0 A
0,5 A
R
+
-
24 V
max.
Inductive
Load
Flyback
Diode
(required for
inductive
loads)
IO
Output
Output Ratings
NO
NC
COM