LUDLUM 4525 Скачать руководство пользователя страница 93

Страница: 93 / 106

Model 4525 Gate Monitor

Operator’s Manual

Ludlum Measurements, Inc.

Page 85

May 2018

SYMPTOM

POSSIBLE SOLUTION

AC Fail

Check to see if AC voltage is
present at the power supply.

Check all fuses.

SYMPTOM

POSSIBLE SOLUTION

Printer Failure

Check that there are not two
versions of the printer driver

installed.

Check that there is only one file

for the printer.

Check if printer is out of paper

or ink.

Troubleshooting RPM-to-Computer Connection

Use the IPSetup utility to verify that all RPMs are found.

If the Model 4525 is shown:

Make sure the subnet mask is the same for the RPM and the
computer.

The default IP address on the system outside should be
192.168.200.1, or similar to it.

The normal setting for the Supervisor IP address should be
192.168.200.2, or similar to it.

See pages 42-44 for information about

Configuring/Assigning Lanes.

If the Model 4525 is NOT shown:

Make sure the RPM is on.

Check to see if Ethernet wires are connected.

Check the cross-over cable and replace if necessary. For information
about the cross-over cable, please refer to the Installation manual.

Содержание 4525











































































































Результаты поиска

Содержание 4525

Отзывы:

Похожие инструкции для 4525

Бренды по названию

Популярные бренды

LUDLUM 4525, Руководство оператора

Результаты поиска

Содержание 4525

Отзывы:

Похожие инструкции для 4525

Бренды по названию

Популярные бренды